Advice
Connecting a decoder to a smart TV without guessing
Most decoder connections are one cable and one menu, and the ones that go wrong nearly always go wrong at the same three points. Here is the order to do it in and what each symptom is telling you.

A satellite decoder is a source, like a game console or a DVD player. It produces a picture and the television displays it. That is the whole relationship, and understanding it that way saves a lot of frustration, because it means the television has no idea what a decoder is and no opinion about it. It is simply showing you whatever is arriving on the socket you have told it to look at.
This applies equally to a DStv decoder and to an OpenView OV512. The satellite side is different, the box is different, the menus are different, but the connection to the television is the same job with the same failure modes.
One cable does the whole job, and it matters which one
HDMI carries the picture and the sound down a single cable. There is no separate audio lead to run and no red and white plugs to worry about. Take the cable from the socket marked HDMI OUT on the decoder to any socket marked HDMI on the television, and make a note of which number that socket is. That number is the only piece of information you actually need for the next step.
Push both ends in properly. HDMI connectors are friction fits with no locking mechanism, and a plug that is ninety per cent home will often give you nothing, or give you a picture that fails when someone walks past the cabinet. If the television is on a wall bracket, feed the cable before the set goes up rather than after, which is one of the small reasons mounting and connecting are better done in the same visit.
Cable quality is worth a sentence and no more. A short HDMI cable from a reputable shop will carry anything a decoder produces. Long runs behind cabinetry or through a ceiling are where cheap cable starts to fail, and the symptom is distinctive: a picture that sparkles, drops out in bursts, or works at one resolution and not another. That is not the decoder and it is not the set.
Getting the television to look at the right socket
This is where most first-time connections stall. The set is on, the decoder is on, and the screen says there is no signal, because the television is still displaying whatever input it was on before. Press the button marked Source, Input or with a rectangular arrow symbol on the television's own remote, and step through the list until you reach the HDMI number you noted.
Two things make this harder than it should be. First, many sets list every HDMI socket regardless of whether anything is plugged into it, so you may cycle through three empty ones. Second, a set that has been renamed by a previous owner may show a label like Blu-ray on the socket your decoder is now using. Go by the number on the back of the television, not by the name on the screen.
- Both ends of the HDMI cable pushed fully home
- The decoder switched on at the plug and out of standby, with its own light showing
- The television set to the HDMI number the cable is actually in
- The decoder's remote used for the decoder, the television's remote used for the input
Once it works, most televisions let you rename the input and some will switch to it automatically when the decoder wakes up. Both are worth setting on the day, because the household member who only ever uses one remote will otherwise phone you every week.
Picture but no sound, and the settings that usually cause it
This is the most common complaint after the input problem, and it has a small number of causes that are quick to work through.
The television's audio output is pointing elsewhere
If a soundbar or amplifier was ever connected, the set may still be sending its audio to an external device that is switched off or unplugged. The setting is usually under Sound, then Speakers or Audio Output. Set it back to the television's own speakers and the sound returns immediately.
The decoder is outputting an audio format the set cannot handle
Decoders can be set to pass through surround formats rather than converting them. A television with ordinary stereo speakers may then produce silence on some channels and sound on others, which is the giveaway. Changing the decoder's audio setting from the surround option to the stereo or PCM option fixes it, and it is done on the decoder's menu, not the television's.
The soundbar in the middle has lost its handshake
Where the decoder feeds a soundbar and the soundbar feeds the television, all three devices have to agree with each other. They lose that agreement after a power cut and do not always recover on their own. Switch everything off at the wall, wait a minute, then switch on in order: television first, then soundbar, then decoder. This resolves a genuinely large share of no-sound calls.
If none of that helps and the set is also silent on its own apps, the fault is in the television rather than the chain. Our article on the six families of television fault covers what an amplifier fault looks like next to a blown speaker.
Sets with two HDMI ports and four things to plug in
Older and smaller televisions often have two HDMI sockets, and a household with a decoder, a games console, a streaming stick and a soundbar has run out before it has started.
An HDMI switch is the straightforward answer. It takes several inputs and presents one output to the television, either with a button or automatically. They work, and the failure mode when they do not is easy to recognise: a picture that appears on some sources and not others, or a switch that keeps jumping to the wrong input. Buy one that is powered rather than one that draws its power from the socket, and expect to spend a little more than the cheapest option on the shelf.
Two things are worth knowing before you buy. A switch adds a device that can lose its handshake, so it becomes the first thing to power-cycle when something stops working. And if a soundbar is in the chain, plan the order deliberately rather than discovering it: usually everything into the switch, switch into the television, television back to the soundbar on the socket marked ARC.
The other answer is to stop treating the television as the hub. Put the sources into the soundbar or amplifier if it has enough inputs, and run one cable to the set. This is often tidier and it means adding a device later does not mean rethinking the whole cabinet.
Older televisions and decoders that predate HDMI
Plenty of working televisions in Cape Town homes have no HDMI socket at all, and they are not scrap. A set with the round yellow, red and white sockets, or with a SCART socket, can usually be fed from a decoder that offers matching outputs. The picture will be standard definition because that is what those connections carry, which is a limitation of the cable standard rather than a fault in anything.
Where the decoder is HDMI-only and the television is not, a converter box is required rather than a simple adapter cable, because the signal has to be actively changed rather than just rewired. Converters vary a great deal in quality and the cheap ones introduce lag and colour problems. We would rather advise on this before you buy than diagnose it afterwards. The same question comes up on nearly every OV512 installation in a house that has kept an older second set.
What to check before deciding something has failed
Before you conclude the decoder or the television is broken, prove where the fault sits by changing one thing at a time. Move the cable to a different HDMI socket. Try a different cable. Plug something else into the socket the decoder was using. Plug the decoder into a different television if there is one in the house.
Each of those isolates one part of the chain. A decoder that works on the bedroom set and not the lounge set has proved itself. A socket that works with a console and not the decoder has proved itself too. Only when the decoder fails everywhere is the decoder actually the suspect, and at that point our page on DStv decoder faults and error codes is the next stop. A decoder showing a satellite error code, incidentally, is not a connection problem at all: it is receiving power and talking to the television perfectly well, and telling you about something happening outside on the dish, which belongs with signal faults instead.
If the cabling is the awkward part
A decoder in one room and the television point in another is a cabling job rather than a connection problem, and running a proper point is usually cheaper than living with a cable across the floor. See cabling and extra TV points, or multiroom installation where more than one set is involved. We cover Cape Town from Thornton, including Goodwood and Parow.
Questions we get asked
Which HDMI port should the decoder go into, and does it matter?
The television keeps switching back to the wrong input by itself. Can that be stopped?
I have a picture but no sound at all from the decoder. Where do I start?
The sound works on some channels and not others. Is the decoder faulty?
Does a longer or more expensive HDMI cable make any difference?
Every port is taken. Is an HDMI switch a reasonable answer or a source of trouble?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za