DStv · Cape Town

Explora installation and setup

Most of an Explora installation happens outside the room the decoder ends up in. The box takes minutes to connect; the dish, the LNB and the cable between them decide whether it still works in five years.

Technician connecting a satellite decoder behind a wall-mounted television

We install Explora decoders in houses, flats and complexes around Cape Town, either as a first satellite installation or as a replacement for a box that has been sitting in the same TV unit for years. We are an independent installer. The physical work is ours — line of sight, mounting, LNB, cable, terminations and getting a picture on your television. Activating the subscription itself sits with MultiChoice.

That split matters more than it sounds, because it is the reason two Explora installations at the same price can behave completely differently. Nothing about the decoder changes. What changes is whether the dish was mounted into something solid, whether the connector at the wall was made up properly, and whether the LNB feeding it can actually carry what the installation is asking of it.

What an Explora install actually involves

  1. Finding the line of sight

    The dish needs a clear view of the satellite. A tree that has grown, a parapet wall, a neighbour's new second storey or a lift motor room on a block roof will all sit in the way, and no amount of tuning fixes an obstruction. We walk the property first and pick the position from what we can see, not from where the last installer happened to drill. More on that on our dish installation page.

  2. Mounting it so it stays put

    Cape Town wind is the main enemy of a satellite installation. A dish on a flimsy bracket, or one bolted into soft plaster or hollow brick, will move — not dramatically, just enough to drop the signal on the days you most want to watch something. We fix into solid material, and if the only solid material is in an awkward place, we say so before drilling.

  3. Choosing the LNB

    The LNB is the part on the arm in front of the dish, and it determines how many feeds the installation can carry. MultiChoice recommends the DStv Smart LNB for all DStv Explora installations in single-unit dwellings. In a complex or a block of flats the answer is different, which we cover further down.

  4. Running and terminating the cable

    The cable route is planned so it is not stapled across a sunny wall or left to swing in the wind. Connectors are made up properly and anything outdoors is sealed. This is dull work and it is also the single most common reason we get called back to somebody else's installation — see cabling and TV points.

  5. Connecting up and checking the signal

    Decoder to television, power to a wall plug, smartcard in, and then we check the signal properly rather than declaring victory because a picture appeared. A marginal installation shows a picture on a clear day. We want headroom left over for the days when the weather is doing something.

A first installation on a house with a clear northern aspect is straightforward. The jobs that take longer are the ones where the obvious dish position does not work — deep verandas, heritage-controlled frontages, tall neighbours, or gardens with mature trees where a pole mount away from the house is the only honest answer.

The single-cable question

DStv describes the Smart LNB as a unit that "combines the features of a DStv Switch into a single UniCable LNB and offers a single cable solution for distribution of multiple satellite signals". In plain terms, it lets one cable carry what used to need several, which is why it turns up on so many Explora quotes.

MultiChoice recommends it for all Explora and most XtraView installations in single-unit dwellings, and states plainly that it is not suitable for Multiple Unit Dwellings — complexes and apartments. If you live in a block, that one sentence saves a lot of arguing, and we have written it up properly on our page about installations in complexes and apartments.

Errors that turn up in the first week

A new installation occasionally throws a code before you have had a chance to get used to the thing. These are the ones we are asked about most, with DStv's own descriptions alongside what we would look at first.

CodeDStv's descriptionFirst thing we check
E48Searching for SignalCable, connectors and LNB before the dish itself
E48-32WeatherWhether it clears when the weather does
E04Please insert smartcardThat the card is seated the right way round
E05Unknown SmartcardThat the card belongs with this decoder
E06Smartcard FailureThe card and the slot, in that order

DStv attributes E48-32 to stormy weather and rain, and tells you to check that the cables from the satellite dish are connected to the decoder properly, then to switch the decoder off at the wall plug and wait at least ten seconds before switching it back on. That advice is worth following before phoning anybody. A dish that only drops out in a howling south-easter and recovers afterwards is a different diagnosis from one that never locks on at all, and we have set out both on DStv signal problems.

Replacing an older decoder

Plenty of our Explora work is a swap rather than a new installation. The question is always what can be reused. Often the dish is fine, the bracket is fine, and only the LNB and a length of cable need attention. Sometimes the existing cable was run twenty years ago behind a skirting that has since been painted over four times, and the sensible move is a new run rather than fighting the old one.

We check before we quote, and we tell you which of the two you are looking at. If the old installation is sound, we say so — there is no version of this job where we make more money by pretending your dish is finished.

Before we arrive

Two minutes of preparation saves a return visit.

  • Know which television the decoder is going on, and whether it is coming off a wall bracket
  • Make sure there is a working plug point within reach of where the decoder will sit
  • In a block or complex, check who controls roof access and whether we need to be signed in
  • Have the smartcard and decoder details handy if the box is already in your possession

Where we do this work

We are based in Thornton and work across the metro, from the Atlantic Seaboard through the Southern Suburbs to the Northern Suburbs and the West Coast. Explora installs in Constantia tend to be about tree cover and long cable runs; in Table View they are about wind and sealing. The general approach is on our DStv installation page.

Questions we get asked

Can I use the dish that is already on my roof?
Usually yes. If the dish is the right size, mounted solidly and pointing where it should, the work is often limited to the LNB, the cable and the connectors. We check it before quoting and tell you plainly whether it is worth keeping or whether it has reached the end of its life.
Do I need a Smart LNB for an Explora?
MultiChoice recommends the Smart LNB for all DStv Explora installations in single-unit dwellings, so in a freestanding house it is the normal answer. In a complex or apartment block it is not — MultiChoice states the Smart LNB is not suitable for Multiple Unit Dwellings.
Do you activate the subscription as well?
No. We are an independent installer, so we do the physical installation and get a picture on your screen. The subscription and the smartcard side of things is between you and MultiChoice. We will tell you what the decoder is showing so that call is a short one.
The picture disappears when it rains and comes back afterwards. Is the installation wrong?
Not necessarily. DStv lists E48-32 as its weather code and attributes it to stormy weather and rain. Heavy rain will interrupt a perfectly good installation. What is not normal is dropping out in ordinary wind, or taking hours to recover, and that usually means the installation has no signal headroom to spare.
Will an Explora run off a communal dish in a block?
In most blocks, yes, and it is common work for us. We are connecting to the building's distribution rather than putting up a dish, so what is possible depends on how that system was built and on what the body corporate permits.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za