OpenView · Cape Town

Getting an OV512 connected and scanned in

The decoder is the quickest part of an OpenView installation and the part most people can manage themselves. Here is the order it happens in, what tends to catch people out, and what to check before deciding the box is faulty.

Coaxial and HDMI cables connected to the back panel of a satellite decoder

An OV512 does nothing on its own. It needs a feed from a dish that can see the sky to the north-east, a cable that arrives in one piece, and a television with a working input. Get those three right and the setup takes minutes. Get one of them wrong and you can spend an evening in the decoder's menus solving a problem that is on the roof.

So this page starts outside and works inwards, which is also the order we work in on site.

What has to be right outside before the box goes on

OpenView works off a satellite dish that points north-east, and it does not care whose dish it is. If there is already one on your wall - a redundant DStv one counts - it is worth testing before anything is bought or replaced. If there is no dish, one has to go up in a position with a clear line of sight in that direction, which is a job of its own and is covered on dish installation and alignment.

The cable matters more than people expect. Satellite cable and old aerial cable are not the same thing and are not interchangeable, and a decoder fed by the wrong cable will either find nothing or find channels that break up on a windy afternoon. Where a house already has a run through the wall, we test it rather than assume it, because a good existing run saves a genuinely useful amount of work.

Before you unbox the decoder

Five minutes with these four questions saves most of the frustration we get called out to.

  • Is there a dish, and can it still see the sky to the north-east without a tree or a new wall in the way
  • Does a cable actually arrive in the room where the television is
  • Does the connector on the end of that cable look dry and intact, or green and crumbling
  • Does the television have a spare input, and do you know how to select it

Connecting the OV512 to the television

The satellite cable screws onto the input on the back of the decoder. Hand tight is right - it should not spin freely, and it does not need a spanner. The decoder then connects to the television, which on any set made in the last fifteen years or so means HDMI: one cable carrying both picture and sound, into a spare port. On an older television the connection depends on what outputs the decoder has and what inputs the set will accept, so it is worth confirming that before anything is bought rather than after.

Once it is connected, the television has to be told to look at that input. This is where a surprising number of no-picture calls end: the decoder is fine, the dish is fine, and the set is showing HDMI 1 while the decoder is plugged into HDMI 2. Cycle the source button on the television remote through every input before concluding anything is broken.

If every input on the television is already used

Older sets frequently have one HDMI port and it is occupied. An HDMI switch is the simple answer, and swapping cables by hand is the free one. If the television has developed a port that only works when the cable is wiggled, that is a repair rather than a workaround - see TV repairs for what that involves.

The first channel scan

  1. Power up with the satellite cable already connected

    The decoder looks for the feed as it starts. Connecting the cable afterwards usually works but starting with everything in place removes one variable from the evening.

  2. Work through the decoder's own setup

    First-time setup runs on the screen. Follow it in order rather than skipping ahead to the channel list, because the scan at the end of it is what fills that list.

  3. Watch the signal reading rather than the channel count

    The decoder shows you what it is receiving. A reading that sits comfortably in the good part of the scale is the sign of an installation that will still be working next winter. A reading that only just gets there is the sign of one that will drop out in the first hard south-easter, even though every channel is present tonight.

  4. Let it run before you accept it

    Leave it on a channel for twenty minutes or so. A marginal feed looks perfect for the first two minutes and starts breaking up once you have put the ladder away.

If the scan finds nothing at all, the problem is almost never the decoder. It is the feed reaching it. No signal and weak signal on OpenView works through that in the order a technician would.

Putting the decoder on your home Wi-Fi

The OV512 offers additional on-demand content over Wi-Fi, so it wants your network password at some point. This is optional. The satellite channels arrive down the dish feed and do not need the internet, and plenty of households never connect the box to anything.

Where it does get connected, the thing to test is whether the signal is genuinely good at the television rather than good at the router. Lounges at the far end of a house, thick internal walls and free-standing units full of electronics all thin a Wi-Fi signal out. If the on-demand side buffers while the satellite channels are perfect, the network is the suspect and the decoder is not.

A second television, a cottage or a flatlet

One decoder feeds one television. A second screen in another room needs its own decoder and its own feed from the dish, which is a cabling job rather than a decoder job. Because OpenView carries no monthly subscription fee, the running cost of that second box is nothing, which is why so many of these installations end up as two rather than one.

The existing LNB and cabling either can carry a second feed or cannot, and that is worked out on site rather than guessed at. Households that are keeping DStv on the main set and adding OpenView elsewhere are in the same position - the question is what the dish and the cabling can already do. Our OpenView installation page covers how that decision usually goes, and the DStv installation hub explains the same four parts from the other side.

Setting up in a flat where the dish is not yours

In a block with a communal dish, your side of the job is usually the wall point inwards: a cable from the plate to the decoder, and the decoder to the television. What the building's system actually delivers to that plate is decided by the body corporate's installation rather than by you, and it is worth establishing that before buying hardware.

In a rented house, anything fixed to the outside of the building needs the landlord's agreement, because a bracket means holes in someone else's wall. Where there is already a dish and a cable run, the whole question usually falls away - one of the practical advantages of a service designed around a dish that is already there.

Questions we get asked

Can I set the OV512 up myself?
If there is already a working dish and a cable at the television, yes - it is a cable, an input and the on-screen setup. The part that usually needs a technician is everything before that: getting a dish aimed properly, or working out why the feed reaching the decoder is not good enough.
My television is old and has no HDMI. Can it still be connected?
That depends on the outputs on the decoder and the inputs your set will accept, and it is much better established before you buy anything than afterwards. Tell us the make and rough age of the television when you phone. An older set is often connectable, sometimes with an adapter, and occasionally it is the point at which replacing the television becomes the cheaper conversation.
The decoder is on and the screen says no input. Is the decoder faulty?
Almost certainly not. That message comes from the television, not the decoder, and it means the set is looking at an input that has nothing plugged into it. Press the source or input button on the television remote and step through every option before assuming anything has failed.
Where should the decoder sit, and does that matter?
Anywhere with air around it. Decoders run warm and the ones that fail early are usually the ones stacked under something else in a closed cabinet. Keep the vents clear and keep it off the floor where it will collect dust.
Do I need a new dish if I have never had satellite TV at this house?
Only if there is nothing usable already. OpenView connects to an existing satellite dish pointing north-east, so previous owners and previous tenants often leave behind exactly what is needed. We would rather test what is on the wall than sell you a dish you do not need.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za