OpenView · Cape Town

No signal on OpenView, and where to start looking

There is no subscription behind OpenView, so a picture that has gone missing is always a physical problem. The useful question is not what has broken but where, and the pattern of the fault answers that better than most people realise.

Satellite signal meter connected to the coaxial cable at a dish arm

With a subscription service, a blank screen has two possible families of cause: the installation, or the account. OpenView has no monthly subscription fee, which removes the second family entirely. What is left is the dish, the cable, the connectors, the LNB and the decoder - in that order, because that is roughly the order in which they fail.

Everything gone, or only some of the channels

This is the first thing we ask on the phone and it splits the problem in half. If every channel has gone, the feed is not reaching the decoder or the decoder is not working. That is a signal fault and this is the right page.

If most channels are fine and a handful are missing or have moved, that is not a reception problem at all. Line-ups change, channels are added and dropped, and a decoder that has not scanned in a while will be out of date. Rescanning is free and takes a couple of minutes, and it resolves a fair number of the calls that come in described as a signal fault.

Three checks worth doing before you phone anyone

  1. Check the connector at the back of the decoder

    It gets nudged loose when the unit is moved for dusting or when something else is plugged in behind the cabinet. It should be finger tight and should not spin freely. This costs nothing to check and it is the single most common thing we arrive to find.

  2. Switch the decoder off at the wall, not on the remote

    Standby is not off. Use the wall switch, count to ten properly, then switch it back on and let it start from cold. Decoders that have been running for months sometimes need exactly this and nothing more.

  3. Look at the dish from the ground, in daylight

    You are looking for anything that has changed: a branch that has grown across the view, scaffolding, a new wall, a dish that is visibly hanging at a different angle from the one you remember. Do not touch it or try to adjust it - just look, and tell us what you saw.

If all three come up clean and the picture is still missing, the fault is between the LNB and the decoder and somebody needs to get to it.

The messages on an OpenView screen are not DStv error codes

People arrive here having read about E48 and its relatives, and try to match them against what their OV512 is showing. Those codes belong to DStv's own decoders and to DStv's published list - they are covered on our DStv signal problems page and they do not translate. Describe what you are actually seeing on the screen instead, in your own words. It is more useful to us than a code copied off a different manufacturer's list.

Why a dish that stood unused can be marginal from day one

OpenView connects to an existing satellite dish pointing north-east, and reusing a redundant DStv dish is one of the reasons the service is cheap to get into. It is also the reason for a particular kind of call we take: the installation worked, and then it did not, and nothing was touched in between.

A dish that spent three years unused was still outside for those three years. The bracket bolts have been relaxing, the connector at the dish end has been taking on damp every winter, the LNB has been through however many summers of ultraviolet, and the cable sheathing has been going brittle. None of that stops the system working on the day it is scanned in. All of it shortens how long it keeps working. When we recommission an old dish we open the connectors, check the mounting and test the LNB rather than simply pointing the decoder at what is already there - dish installation and alignment covers what that involves.

Weak signal: the picture that breaks up rather than disappears

A weak feed is more annoying than a dead one and much easier to live with for too long. It shows as pixelation on some channels, a picture that freezes for a second and carries on, or reception that is fine in the morning and poor by late afternoon. The installation is working, but with nothing in hand, so anything that takes a little away - heat, wind, a wet tree - takes it below the line.

What you are seeingWhat it usually meansWhere we look first
Nothing at all, and a rescan finds no channelsThe feed is not arriving at the decoderThe connectors, the cable run, then the LNB
Everything breaks up at once, worst in windThe dish is moving, or the aim is only just good enoughThe bracket, the clamp bolts and the aim
Fine normally, gone in heavy rain, back afterwardsOrdinary satellite behaviour - unless it is newNothing, if it recovers cleanly. A connector, if it never used to do this
Slowly got worse over monthsSomething has grown into the line of sight, or a connector is corrodingThe view to the north-east, then the connections
One television is fine, another has nothingThe fault is on that leg, not at the dishThat run, its splitter and its connections

The last row is worth dwelling on. If one decoder in the house is happy and another is not, the dish has already proved it is working. Nobody needs to go up a ladder to establish that, and the job becomes tracing one cable run - which is quicker and cheaper than everyone assumes when they phone.

Wind, rain and the Cape south-easter

Heavy rain interrupts satellite reception and then it comes back. That is how the technology behaves and it is not a fault. What is a fault is an installation that used to shrug off a front and now drops out in every shower, because that change is telling you something got worse. Usually it is water in a connector, occasionally a cracked cable sheath, sometimes an aim that has crept.

Wind is a different diagnosis from rain. A picture that fails when it is blowing and returns when it is still is mechanical - the dish or the bracket is moving. That gets worse rather than better, because whatever is loose keeps working itself looser. Both of these are inexpensive while they are still intermittent, which is the argument for dealing with them in autumn rather than in the middle of August.

If the feed turns out to be fine and the box is the suspect, OpenView decoder problems is the next page. If you are setting up for the first time and have never had a picture at all, start at decoder installation and setup, because a first-time installation that has never worked is a different problem from one that has stopped.

Questions we get asked

My OpenView ran on an old DStv dish for a year and has now stopped. What changed?
Time, most likely. A dish that stood unused for years was still weathering the whole time, so its connectors, bracket bolts and LNB start from further along than a new installation does. The system was working with very little in reserve, and something ordinary has used the last of it up.
A few channels have disappeared but the rest are fine. Is that a signal problem?
Usually not. Reception faults take everything or almost everything, because they affect the feed rather than individual channels. A handful of missing channels is far more often a line-up change, and a rescan on the decoder puts it right at no cost.
Would a bigger dish give me a stronger picture?
It is rarely the answer and it is often an expensive way to avoid fixing the real fault. Aim, a sound connector and a clear view to the north-east do more for a marginal installation than size does. We would rather test what you have before anyone buys a bigger reflector.
My neighbour's OpenView works and mine does not, on the same street.
That tells you the fault is at your house rather than with the service, which is genuinely useful. Two houses a few metres apart can have completely different views of the sky, and they certainly have different dishes, cables and connectors of different ages.
Should I rescan the decoder before calling someone out?
Yes, it is free and it takes a few minutes. A rescan fixes missing or moved channels, and if it comes back having found nothing at all, that is a clear result too - it means the feed is not reaching the box, which is worth telling us when you phone.
Can I nudge the dish myself to see if it improves?
We would rather you did not. The movements that matter are very small, a dish that is slightly out is easy to put badly out, and once the original position is lost it takes considerably longer to find again. Leave it and tell us what you have observed instead.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za