TV Repairs · Cape Town
TV wall mounting that stays on the wall
A mount is only as good as what is behind the plaster. Most of the failures we are called out to are not bracket failures, they are fixings that were put into the wrong material and held for a while.

Mounting a television is two jobs: getting it level and getting it safe. The first is what people watch you do. The second is the one that matters in two years' time, and it is decided in the first ten minutes, before a hole is drilled, by working out what the wall is actually made of.
The wall decides what is possible
Cape Town homes throw up all of these, often in the same house:
- Solid brick and plaster: the straightforward case, and the strongest. Fixings go into brick, not into the plaster skin over it
- Hollow block: common, and it needs the right anchors placed where there is material to grip. A standard plug spinning in a void holds nothing
- Drywall or a partition wall: mountable, but only into the studs behind it or with fixings rated for the load. The board itself carries nothing
- Concrete: strong, and it needs proper drilling rather than an impatient hammer drill and a blunt bit
- Timber-framed and dry-walled additions: fine when the framing is found and used, poor when it is guessed at
- Face brick and stone: workable, with the fixing placed in the brick rather than in a mortar joint
We check what is behind the surface before committing to a position, and we scan for cables and pipes in the drill line. That last part is not optional. A drill bit through a concealed conduit turns a straightforward afternoon into an electrician's problem and a hole in your wall.
Fixed, tilting and full-motion
Three families of bracket, and the right one comes from where you sit rather than from what is on offer.
Fixed and flat
The set sits close to the wall and does not move. It looks the best, it is the most secure, and it is the right choice when the television is at eye level from where you actually watch. The compromise is access: getting to the ports behind the set is awkward, so cabling has to be planned before it goes up.
Tilting
Allows the screen to angle downwards, which is the answer when a set has to go higher than ideal, above a fireplace for example. It solves the viewing angle, though it does not solve the neck ache that comes from a screen mounted too high in the first place.
Full-motion or articulated
The arm swings the set out from the wall and turns it. This is what you want in an open-plan room where the lounge and the kitchen both need a view, or in a bedroom where the screen must face the bed and a corner at the same time. It puts far more leverage on the wall than a flat bracket does, so the fixings and the wall material matter more, not less.
Whichever type, the bracket has to match the set. Weight rating with margin, and the correct VESA hole pattern on the back of the television, which is the standard spacing brackets are made to. Sending a photograph of the back of your set and its model number before we come out means we arrive with hardware that fits.
Height, angle and the light in the room
The most common regret we hear is that the television went up too high. The comfortable position puts the centre of the screen at roughly eye level when you are seated, which on most lounge sofas is lower than instinct suggests. Screens have grown, and a big set mounted at the height that suited a small one leaves you watching with your chin up for the length of a film. We do this in homes all over the city, from flats in Sea Point to houses in Durbanville, and the height question comes up on nearly every one.
Above a fireplace is a special case. It is often the only wall available, and it is higher than ideal, warmer than ideal and sometimes has a mantelpiece that stops the set sitting flat. A tilting bracket helps. We will tell you honestly if we think the position is going to be uncomfortable, and where else in the room might work.
Then there is glare. In a Cape Town lounge with a big western window, an afternoon reflection can make a screen unwatchable at exactly the hour people want to use it. It is worth standing where you sit, at the time of day you watch, and looking at what will be reflected in a large dark rectangle on that wall.
Mark it before you drill it
We put the bracket position on the wall in tape at the actual height and let you sit down and look at it before anything is fixed. It takes two minutes and it is the cheapest possible time to change your mind.
Cables: hidden properly or hidden badly
A neatly mounted television with four cables hanging down the wall is a job half done. There are three honest ways to deal with it.
Into the wall
The tidiest result: the cables run inside the wall from behind the set to an outlet lower down, usually behind a cabinet. It suits a solid or a drywall wall, it means chasing and making good on a plastered wall, and it should never include a mains lead run loose inside a cavity. Power belongs in a proper socket.
Trunking or a cable channel
A slim channel on the wall surface, painted to match. Far less work, no damage to the plaster, and once painted it is much less visible than people expect. This is often the right answer in a rented home, where drilling and chasing are not on offer.
Down the back and out of sight
Where the set sits above a unit, the cables can drop straight into it and never be seen. It costs nothing and it works, provided the equipment lives directly below the screen.
While the wall is open is also the moment to think about what else should be behind that television: an aerial or satellite point, a network cable to the set, a spare HDMI run to wherever equipment might move to later. Doing it now is straightforward and doing it afterwards means opening the same wall twice. Cabling and TV points covers how we run those.
What makes a mount safe
- Fixings into solid material, chosen for that material, not the plugs that came in the box
- A bracket rated well above the weight of the set, not just up to it
- The correct VESA pattern, with bolts of the right length for that television
- The load spread across the fixings, and the bracket level on both axes
- Nothing drilled into a cable run, a water pipe or a conduit
- The set tested on the bracket before we leave, including a firm hand on it
- Cables with enough slack that nothing pulls on a port when the set is moved
If your set is already on a wall and you are having it repaired, we check the bracket and the fixings while it is down, because it costs nothing to look and a screen coming off a wall is an expensive way to find out. That is part of every repair visit; see TV repairs in Cape Town for what else is included.
Mounting a new set after an old one has failed
Plenty of mounting jobs start as a repair that did not go ahead. If you are still deciding, screen replacement explains when a set is worth fixing, and we will happily hang the replacement and take the old one off the wall on the same visit.
Questions we get asked
Can a television be mounted on a drywall or partition wall?
How high should the screen go above a fireplace?
Can the cables be hidden inside the wall?
I already bought a bracket. Will you fit it?
Can you mount a television outside, on a patio or a braai area?
Can you take the old bracket down and repair the wall?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za