OpenView · Cape Town

Dish work for OpenView, from a new mount to a drifted aim

OpenView connects to an existing satellite dish pointing north-east, which means a good share of this work is recommissioning something that is already on the wall rather than putting up something new.

Technician on a ladder adjusting a satellite dish fixed to a house wall

Two jobs sit on this page and they start from very different places. One is a house with no dish, where a position has to be found and a bracket has to go into a wall. The other is a house with a dish that has been up for years, often left behind when a subscription was cancelled, which needs testing rather than replacing. The second is more common and it is much the cheaper of the two.

Recommissioning a dish that is already on the wall

The instruction we give most often on the phone is to leave the old dish exactly where it is. People take them down out of tidiness before we arrive, and it turns a short visit into a full installation. A dish that has done nothing for three years is still a dish, a bracket, a cable through the wall and a hole that is already sealed - all of which somebody paid for once.

What we go through is a fixed list, and any item on it can be dealt with on its own without touching the rest.

  • The bracket and its fixings - whether they are still solid and still in something that will hold them
  • The dish itself - a dented or twisted reflector will not focus properly no matter how well it is aimed
  • The LNB on the end of the arm, which has been powered and outdoors for its whole life
  • The connectors at both ends, which are where water gets in and where corrosion starts
  • The cable run into the house, and whether it is satellite cable or something that was pressed into service
  • The line of sight to the north-east, which may have had a tree or a neighbour's second storey added to it since

The usual outcome is that the mounting and the dish are fine and one or two of the smaller parts have had enough. That is a good result: the expensive, awkward part of a satellite installation is the bit that involves a ladder and a masonry drill, and it is already done.

Choosing a position when there is no dish yet

Where nothing is up, the position is decided by what the dish can see rather than by where it would look best. It needs a clear line of sight to the north-east, and that is not a preference we can work around. Within that constraint we will always take the more discreet option, and on many houses a side wall or a gable end satisfies both at once.

The second consideration is where the cable can get into the house without a long run down the front of it, and the third is what is going to be there in ten years. A sapling below the dish line today is a problem in five winters, and a single-storey neighbour is not a permanent arrangement. Our DStv installation pages go through the same decision from the subscription side, and dish installation and mounting has more on how positions get chosen.

The mounting decides how long the installation lasts

The aim is only ever as good as the thing holding the dish still. Fixings go into solid material - not into plaster, not into a hollow block, not into a fascia board that will soften after a couple of wet winters. If the wall we would prefer turns out to be soft, we move the position rather than hope for the best.

Cape Town supplies its own argument for this. A dish that is on a slightly undersized fixing works perfectly all summer and starts breaking up the first time the south-easter really blows, and by then the fixing has been working itself loose for months. A dish that does not move in wind is a dish that will hold its aim for years without anybody thinking about it.

Bringing an aim back, and why it is done on a meter

Aiming is not something that can be judged by eye. The movements that make the difference are very small, and a dish that looks exactly like it always did can be far enough out to have lost half its signal. That is why the job is done with a meter on the cable and then confirmed at the decoder, rather than by watching the picture and guessing.

  1. The mounting is checked and tightened before anything is aimed

    There is no point aiming a dish that is going to move. Loose clamp bolts and a bracket that flexes are dealt with first, otherwise the aim is undone the moment the wind picks up.

  2. The connectors are opened and inspected

    The one at the dish end faces the weather for its entire life. If moisture has been getting in, no amount of aiming will produce a stable picture, and it is far cheaper to remake a connector than to keep chasing the symptom.

  3. The dish is aimed on a meter and then locked down

    Small movements, checked as they are made. A dish shifts slightly as it is clamped tight, so it is checked again once everything is done up - that final check is a step in its own right rather than an afterthought.

  4. The result is confirmed at the decoder

    The reading outside is not the last word. We check what the OV512 is actually receiving indoors and leave it running for a while, because an installation with nothing in reserve looks perfect for the first few minutes. Decoder installation and setup covers that end of the job.

The parts that fail outdoors before the dish does

Reflectors outlast almost everything attached to them. The parts that give up are the LNB, which is powered and exposed for years; the connectors, which are where water finds its way in; and the cable, which perishes in sunlight and chafes where it crosses a gutter or a roof edge. Rodent damage in a ceiling accounts for a steady number of the rest.

Any of those produces the same complaint from the couch - a picture that breaks up, or no picture at all - which is why the diagnosis matters more than the guess. No signal and weak signal on OpenView sets out what the pattern of the fault tells you before anybody gets a ladder out, and dish alignment covers the same ground for subscription installations.

When the wall is not yours to drill

In a rented house, anything fixed to the outside of the building needs the owner or the managing agent to agree, because a bracket means holes in somebody else's wall. Where a dish and a cable run already exist, that question usually disappears, which is one of the quiet advantages of a service built around a dish that is already there.

In a block of flats there is often a communal dish feeding a point in each unit, and the work on your side stops at that wall plate. Where a block has no communal system, a dish on a balcony or an outside wall is a body corporate decision rather than yours alone. It is worth establishing which of those situations you are in before buying any hardware - our OpenView installation page covers how those jobs are usually scoped.

Questions we get asked

We are cancelling DStv. Can that dish carry OpenView?
Very often, yes. OpenView connects to an existing satellite dish pointing north-east, so a redundant dish is worth testing before it is written off. Leave it on the wall until somebody has looked at it - the bracket, the cable and the sealed hole through the wall are all work that has already been paid for once.
Which way does an OpenView dish have to face?
North-east, with a clear view in that direction. That is not adjustable to suit the look of the house, so the position is chosen around what the dish can see. We will not publish angle settings on a web page, because they vary and a wrong number sends people up ladders for no reason.
The dish has been sitting unused for years. Is it still any good?
Usually the reflector and the bracket are fine and the smaller parts have suffered. Connectors take on damp, the LNB weathers, and cable sheathing goes brittle in the sun. Each of those is replaceable on its own, which is why we test before recommending anything.
Will the LNB and cable that are up there work, or do they need changing?
That is decided on site rather than assumed. The dish and its mounting are the parts that carry over most reliably. The LNB, the connectors and the existing cable are tested, and we replace only what does not pass - which on most old installations is one item rather than all of them.
Can I aim the dish myself with an app on my phone?
An app will point you in the right general direction, which is the easy part. The difficulty is that the final adjustments are small, easily lost and hard to recover once the original position has gone. If you have already tried and it is now worse, say so when you book - it is not a problem, it just changes where we start.
A tree has grown in front of the dish. Does it have to be moved?
If the growth is in the line of sight to the north-east, then yes - aiming cannot see through foliage, and wet leaves are worse than dry ones. The alternative is trimming, which works until it grows back. Moving the dish to a position that can see past the obstruction is the fix that lasts.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za