DStv · Cape Town
DStv installation, from dish to decoder
This is the main page for everything we do with DStv. It covers what a standard installation involves, what the technician is doing while he is up the ladder, and where to go for the specific job you need.

A DStv installation is four things done in the right order. A dish goes up somewhere with a clear view of the sky to the north-east. An LNB is fitted to the arm and the dish is aimed and locked down. A cable is run from there into the house and terminated at a wall point. A decoder is connected to the television and brought up. Everything else we do - extra rooms, XtraView, a Smart LNB, a system for a guesthouse - is a variation on those four steps.
We are an independent installation and repair business working out of Thornton, and we cover Cape Town and the surrounding areas. What follows is what actually happens on site, in the order it happens, so you can tell whether the job in front of you was done properly.
What happens on the day
We look at the property before anything is drilled
The first ten minutes decide the next ten years. We find a position with a clear line of sight to the north-east, work out where the cable can get into the house without a long ugly run, and check what is going to grow or get built into that line later. A dish put up in the easiest spot rather than the right one is the single most common reason we get called back to a house we did not install.
The bracket goes up first, into something solid
The bracket carries the whole system, and the aim is only as stable as the thing holding it. Fixings go into solid material - not into plaster, not into a hollow block, not into a fascia board. If the wall we would prefer to use turns out to be soft, we move the position rather than hope.
Dish and LNB are fitted and aimed
The dish is assembled, the LNB goes into the holder, and the dish is aimed on a meter and then locked. The movements that matter at this stage are small. This is also why tightening a bolt is part of the aiming rather than something that happens afterwards - a dish will shift as it is clamped down, and it has to be checked again once it is tight.
The cable is run, clipped and sealed
We pick a route that is protected and reasonably tidy, clip the cable properly rather than stapling it flat, and drill the entry hole so it falls away from the inside of the wall. A drip loop and a sealed entry are the difference between a hole that stays dry and one that quietly ruins the plaster over a couple of winters.
The decoder is connected and the system is tested
The decoder goes onto the television, the signal is checked at the decoder rather than assumed from the meter outside, and we let it run before we pack up. If there is a wall point in another room, we test that one too.
The four parts of the system, and what each one does
The dish
The dish is a reflector and nothing more. Its only job is to collect signal and concentrate it onto the LNB, which means two things matter: where it points, and whether it stays pointing there. A dented or badly distorted dish will not focus properly, and a dish on a bracket that flexes in wind will work on a still day and fail in a gale. If you already have a dish on the wall, it is usually worth keeping - see dish installation and mounting for how we decide on a position.
The LNB
The LNB sits at the end of the arm and does the actual work of converting what the dish collects into something the cable can carry. It is the one part of the system that is both powered and permanently out in the weather, which is why it turns up so often in fault-finding. How many outputs it has determines how many decoders the installation can feed.
The DStv Smart LNB is a different animal. In MultiChoice's own words it "combines the features of a DStv Switch into a single UniCable LNB and offers a single cable solution for distribution of multiple satellite signals", and they recommend it for all DStv Explora and most XtraView installations in single-unit dwellings. The important limit is that it is officially not suitable for multiple unit dwellings, which means complexes and blocks of flats. If you live in one, that changes the plan - see installations in complexes and apartments.
The cable and the wall points
Satellite cable is not aerial cable and the two are not interchangeable. The run from the dish to the decoder should be continuous where it can be, with proper connectors at each end and as few joins as possible in between, because every join is a place for water and corrosion to start. Where a house needs points in more than one room, it is far cheaper to run them while someone is already on site than to come back later. Cabling and TV points covers that in detail.
The decoder
The decoder is the part you actually deal with, and setting it up is the quickest part of the job - connect it, scan, check it holds. Explora installations have their own requirements around the LNB and the cabling, which is why Explora installation has its own page. The one thing no installer can do for you is the account itself: the subscription side sits between you and DStv.
One room, more rooms, or the whole house
Most calls start as one television and become two once someone realises the second room is possible. Doing it at the same visit is straightforward. Doing it eighteen months later usually means new cable through a ceiling that has since been closed up, so it is worth deciding early even if you only connect the second room later.
MultiChoice spells it XtraView. Plenty of people search for "Extra View" and mean exactly the same thing, so if that is the term you have been using, you are in the right place - XtraView installation explains what the setup needs. For houses running several rooms off one system, multiroom installations is the page to read.
Flats, complexes and business premises
A block of flats usually has a communal dish feeding each unit, which changes the job completely. The work is often on your side of the wall only, the body corporate may have rules about what can be fitted to the outside of the building, and a Smart LNB is not the right answer because MultiChoice specifically excludes multiple unit dwellings from its recommendation. We work in blocks regularly and would rather establish all of that on the phone than discover it on the landing.
Guesthouses, restaurants, waiting rooms and offices are a different kind of planning again, because the number of screens and the distances involved decide the whole design rather than being an afterthought. DStv for businesses covers that side.
New builds and houses that already have cabling
If you are building or renovating, the cheapest possible time to put satellite and TV cabling in is before the plaster goes on. It costs almost nothing at that stage and it is a miserable job afterwards. Installations in new homes is written for exactly that window.
In an older house there is often cable already in the walls from a previous owner. Some of it is fine and some of it was never satellite cable in the first place. We test what is there before quoting anything new, because reusing a good existing run is faster and cheaper than pulling a fresh one.
If there is already a dish on the wall
A dish left behind by the previous owner is worth testing before it is written off. Often the dish and the bracket are perfectly serviceable and only the aim has drifted, or a connector has let water in. We check the mounting, the LNB and the cable before we suggest replacing anything.
- The bracket is solid and the fixings have not corroded
- The dish itself is not dented or twisted
- The LNB and the connectors are dry and intact
- The existing cable run is satellite cable and is not damaged
When something goes wrong later
Installations that were done properly still develop faults, because the outdoor half of the system lives through Cape winters. If yours has stopped working, DStv repairs covers fault-finding on an existing installation. If the screen is showing an error, start with signal problems and no-signal errors for the E48 family or decoder and smartcard errors for everything else. If the dish has drifted rather than failed, dish alignment is the one you want, and if you are moving house, DStv relocation covers taking the system with you.
If the problem turns out to be the television
A dead screen, a picture with no sound, or a set that will not switch on is not a satellite fault, even if it looks like one from the couch. We repair televisions as well - see TV repairs in Cape Town, or TV mounting if the screen needs to go on the wall while we are there.
Questions we get asked
Do I need to have the dish and decoder before you arrive?
We are renting. Can DStv still be installed?
What is a Smart LNB and do I need one?
How many decoders can one dish feed?
Can the dish go somewhere it will not be seen from the street?
Do you install for guesthouses, restaurants and offices?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za