DStv · Cape Town

Decoder errors, smartcard faults and overload codes

Not every code on the screen is a job for a technician. Some are about the hardware, some are about your account, and some mean the decoder is simply busy. Knowing which is which saves you a call-out.

DStv decoder on a shelf with a smartcard partly inserted in the slot

The codes below all come from DStv's official error code list. We have grouped them the way we think about them on a call, because the grouping is the useful part: a smartcard message and a subscription message look equally alarming on a television screen, but only one of them is something anybody can fix by driving to your house.

Smartcard messages and what they mean

CodeDStv's description
E04Please insert smartcard
E05Unknown Smartcard
E06Smartcard Failure
E07Checking Smartcard
E33-4Insert correct Smartcard
E100 / E101Smartcard validation failed
E107Smartcard Error

A smartcard is a physical contact device sitting in a slot, so the first thing to rule out is the simplest one. A card that has been taken in and out repeatedly, or one in a decoder standing in a dusty room, can stop making proper contact. Reseating it the right way round, fully home, resolves a reasonable share of E04 and E07 messages.

E33-4 is the one that tends to catch households running more than one decoder, because the cards are not interchangeable between them - a card swapped between two units in the same house produces exactly this message. If you have a linked pair, XtraView installation is worth a read for how the two decoders relate to each other.

Where a card has genuinely failed rather than come loose, we cannot help you. We do not issue smartcards and there is nothing on the installation side that will bring a dead card back.

Codes that are not about your hardware

Subscription messages

CodeDStv's description
E16Service is currently scrambled
E17No Active Subscription
E19Subscription expired
E30Checking the subscription status

This is the honest bit, and it is the reason this section exists. These codes are between you and DStv. No installer, ours included, can change the state of your account, and nothing we do to the dish, the cable or the decoder will clear an E17 or an E19. If that is the message on your screen, a technician visit costs you a call-out and changes nothing. Take it up with DStv directly and you will get it sorted faster and cheaper.

Channel and viewing messages

The same applies to codes that describe what may be watched rather than what is broken. On DStv's list these include E18 ("Channel is not available"), E37 ("Invalid channel number"), E38 and E39 ("Service is not available"), E42 ("Parental Control lock"), E43 (the channel is not available for your country), E45 ("Service not allowed"), E70 ("Service is not available for viewing"), E109 ("Channel currently scrambled") and E118 ("Channel can't be viewed"). None of them describe a fault in your installation.

Overload codes: E73, E74 and E75

These three are hardware messages and they do belong to us. DStv lists E73 as "TV link overload", E74 as "LNB1 overload" and E75 as "LNB2 overload".

An overload message is the decoder complaining about the load on one of its outputs rather than about the picture, which is why it is so often misread as a signal problem. In our experience E74 and E75 usually point at a cable or connector short somewhere in that run rather than at the dish itself, and we treat E73 the same way - we follow the cabling on the affected output rather than starting at the arm.

A short is not always dramatic. A single stray strand of braid touching the centre conductor inside a connector is enough, and that is easy to create when a connector is fitted in a hurry or refitted after a repair. Joins, splitters and any point where somebody has extended a run are the places we look first, which is why cabling and TV points matters more on these faults than anything on the roof.

Messages that mean the decoder is busy

Some codes are the decoder narrating a process rather than reporting a failure. On DStv's list, E32 is "Validation in progress", E72 is "Rescan in progress", E120 is "Synchronization in progress", E600 is "Validation in Progress" and E106 is a notification. The right response to all of them is to leave the decoder alone and let it finish.

People generate real problems here by pulling the plug halfway through. If a decoder is mid-process, let it complete before deciding anything is wrong with it.

Faults that arrive without a code

Plenty of decoder complaints never show a code at all, and these are the ones worth booking:

  • The decoder will not power up, or shows a standby light and nothing more
  • It powers up but there is no picture on the television at all
  • It freezes, or restarts itself repeatedly during viewing
  • It runs very hot and misbehaves worse the longer it is on
  • The remote works intermittently or not at all
  • Sound plays but the picture is missing, or the other way round

The no-picture case is worth separating out before you call anyone. Try a different HDMI cable and a different input on the television. If another device works on that input and the decoder does not, the decoder is the suspect; if nothing works on that input, the television is - and TV repairs is the page for that.

Heat is worth checking yourself

A decoder in a closed cabinet with a Wi-Fi router and an amplifier stacked on it is running hotter than it was designed to. Freezing and random restarts that get worse through the evening frequently improve with nothing more than air around the unit and a few centimetres of clearance above it.

What a technician can and cannot fix

We can trace and repair the cabling, connectors, wall points, splitters and outdoor hardware that produce overload codes and no-signal faults, and we can set a decoder up correctly on an installation. We cannot change your subscription, issue a smartcard or reverse an account status.

If your screen is showing an E48 rather than any of the codes above, the fault is on the signal side of the system and signal problems and no-signal errors is the page to start with. For faults on an installation that has stopped working generally, DStv repairs covers how we work through them, and the DStv installation hub explains how the parts fit together in the first place.

Questions we get asked

My decoder says E17. Can a technician fix that?
No, and we will tell you so rather than take the booking. E17 is DStv's "No Active Subscription" message, which is an account matter between you and DStv. Nothing on the dish, the cable or the decoder affects it.
The screen says please insert smartcard, but the card is already in. What now?
Take it out and put it back in properly, fully seated and the right way round, then let the decoder settle. Cards work loose and their contacts get dirty. If the message survives a careful reseat, the card itself is the likely problem, and that is DStv's side rather than ours.
What does an LNB overload message actually mean?
DStv lists E74 as LNB1 overload and E75 as LNB2 overload. In our experience it points at a cable or connector short in that run rather than at the dish, and it is usually found at a join, a splitter or a connector that was made up in a hurry.
My decoder keeps restarting itself. Is that worth repairing?
It is worth looking at, and the first thing to check costs nothing. Decoders shut inside a cabinet with other equipment overheat, and restarts that worsen as the evening goes on often stop once the unit has air around it. If it still restarts with proper ventilation, book it in.
There is no picture at all from the decoder. Is it dead?
Not necessarily. Try a different HDMI cable and a different input on the television first. If another device plays fine on that input and the decoder still shows nothing, the decoder is the problem; if nothing works on that input, the television is.
The decoder is showing a code I cannot find on this page. What should I do?
Read us the exact code including anything after a dash, because the suffix changes the meaning - E48 and E48-32 are different messages with different causes. With the full code we can usually tell you on the phone whether it is a job for us or one for DStv.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za