DStv · Cape Town
Satellite dish installation and mounting
Everything downstream of the dish depends on two decisions made in the first ten minutes on site: where it goes, and what it is bolted to. Get those right and the installation is quiet for years.

A dish is a simple object doing a fussy job. It has to sit still, keep looking at the same patch of sky, and go on doing that through a Cape winter and a summer of south-easters. Almost every failure we get called to on a dish installation traces back to a mounting decision rather than to the dish itself.
Line of sight decides the position, not looks
The dish needs a clear line of sight to the north-east. That is not a preference, it is the whole basis of the installation, and it means the position gets chosen by what the dish can see rather than by which wall is convenient or least visible from the street.
The things that get in the way are predictable: a chimney, a parapet, the neighbour's roofline, a garage that was added later, and trees. Trees are the one people forget, because the survey happens in the present tense and the tree carries on growing. We look at what is standing in the path today and at what is going to be standing in it in five years, and if a palm or a milkwood is heading for that piece of sky we would rather move the dish now than come back and do it twice.
We do not publish a specific angle to set the dish to, and you should be wary of anyone who does. The aim is set on site with a meter, at that address, because the numbers vary and the only thing that matters is what the dish actually locks onto from where it is standing.
Wall, gable or pole
Wall mount
The default, and usually the right answer. A solid brick wall at a height that can be reached safely for future service, on a face that is out of the worst of the prevailing wind where the line of sight allows it. Low enough to service, high enough to be clear of what is around it.
Gable mount
Where the ground-floor sight lines are blocked, the gable buys height. The trade-off is leverage: the same wind acting on a dish higher up puts more load on the bracket, so a gable mount has to be fixed into something that genuinely deserves it. It also has to be reachable later, because a dish nobody can safely get to is a dish that never gets serviced.
Pole or ground mount
Occasionally the building simply cannot see the right piece of sky and the dish goes on a pole away from the house. It works well, but it needs a rigid base and a longer cable run, and the cable then has to be protected where it crosses open ground.
The mountings we turn down
- Hollow block, or brick that has already been drilled and patched several times
- Fascia boards, gutters and anything fixed only to timber trim
- A carport or a lean-to roof that flexes when the wind gets under it
- A boundary wall that belongs to the neighbour, or is shared
- Anywhere the dish can only be reached by standing on something that was not meant to be stood on
A bracket that does not move in a south-easter
A dish is a sail. That is the whole engineering problem in one sentence. The aim is only as good as the bracket holding it, and a mount that flexes even slightly under load will produce an installation that works beautifully on a still afternoon and drops out every time the wind comes up.
So the bracket goes into solid material with the correct fixings, the arm is kept as short as the sight line allows because a shorter arm means less leverage, and everything is torqued properly rather than nipped up. It is also why we check the mount before doing anything else on a fault call: an installation that fails in wind and recovers in calm weather is almost never an aiming problem, even though that is what it looks like. Dish alignment covers that distinction in more detail.
Coastal sites add corrosion to the list. Salt reaches fixings, brackets and connectors, and on the seaboard and the West Coast we expect to find rust where an inland job would show none - it is a routine part of installations in Bloubergstrand and along that whole stretch.
Cable entry, and keeping water out of the wall
The hole through the wall is where a lot of otherwise decent installations go wrong, and the damage takes two winters to show up. The entry is drilled with a fall to the outside so that anything running down the cable runs away from the building rather than into the plaster, the cable is looped below the entry so water drips off before it reaches the hole, and the hole is sealed properly rather than smeared over.
Outside, the cable is clipped at sensible intervals rather than stapled flat, kept off gutter edges where it would chafe, and routed to be protected instead of merely tidy. Where a house needs more than one point, planning the runs at the same time is far cheaper than opening a ceiling again later - cabling and TV points goes into that.
The connector at the dish end
This single joint causes more service calls than the dish, the bracket and the cable combined. It faces the weather, it is the highest point of the run, and once water tracks into it the corrosion is only going one way. Making it up properly and weatherproofing it is a two-minute job during installation and a whole call-out afterwards.
Dishes on flats, complexes and rented houses
In a complex or a block, the outside of the building is usually not yours to drill, and many blocks already run a communal dish feeding each unit - in which case the work is on your side of the wall and no new dish is needed at all. Body corporate rules vary and it is much better to establish them before a technician is standing on a landing with a bracket. It is also where the Smart LNB stops being an option: MultiChoice recommends it for single-unit dwellings and states that it is not suitable for multiple unit dwellings, which is exactly what a complex is. Installations in complexes and apartments covers how those jobs run.
If you are renting a house, the landlord or the agent needs to agree to a bracket, because it means holes in somebody else's wall. Where that agreement is not forthcoming, an existing bracket or an existing cable run will often do the job with no new penetrations at all. The DStv installation hub sets out what the rest of the system involves once the dish is up.
If the house is still being built
The cheapest moment to place a dish position and get cable into the walls is before the plaster goes on, and it is worth deciding then rather than drilling a finished house. Installations in new homes is written for that stage of a build.
Questions we get asked
How do you decide which wall the dish goes on?
Can the dish go on the roof rather than on a wall?
Will drilling through the wall cause a damp problem?
Can a dish be mounted on a boundary wall or a carport?
Does the dish have to point in a particular direction?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za