DStv · Cape Town
Coax, connectors and extra TV points
Nobody books a technician because they are excited about cable. They book one because the picture keeps dropping, and the cable is usually the reason.

The cabling is the least glamorous part of a satellite installation and the part that decides how long it lasts. A dish is a dish, and an LNB either works or it does not. The run between them and your decoder is where an installation is made or ruined, because it is the part that can be done badly in a way nobody notices for eighteen months.
Intermittent faults are cable faults until proved otherwise
There is a useful pattern in this work. A fault that is there all the time is usually a component — something has failed and it stays failed. A fault that comes and goes is usually mechanical: a connection that is not quite making contact, moving with temperature, wind or somebody knocking the back of the unit.
So when a customer says the picture is perfect for a week and then breaks up for an evening, or that it fails in the afternoon and comes right overnight, we start at the connections rather than the dish. Copper expands in the sun. A cable that is stretched taut over a fascia board pulls harder on its connector on a hot afternoon than it does at six in the morning, and a connector that is only just gripping will let go at exactly that point.
- Breaks up in wind, fine in still weather — something is moving that should not be
- Fine in the morning, poor in the afternoon — heat, and usually a connection under strain
- Fails when someone walks past the unit or moves the decoder — the flex or the wall point
- Fails gradually over months and never recovers — water ingress, corrosion or a degraded cable
Weather is the exception that needs stating. DStv attributes its E48-32 code to stormy weather and rain, and heavy rain will interrupt a perfectly sound installation for a while. The difference is recovery: a good installation comes back as soon as the storm passes, and a marginal one takes hours or never quite returns to what it was. Our page on signal problems works through that distinction properly.
Connectors do most of the failing
If we had to name the single most common defect we find on other people's installations, it is the connector. Specifically: the centre conductor cut too long or too short, the screening braid folded back untidily so a strand touches the centre pin, a connector crimped onto a cable it was not sized for, or one simply pushed on and twisted by hand.
A stray strand of braid touching the centre conductor is a short, and a short on a satellite feed produces exactly the sort of complaint people describe as the decoder being broken. DStv lists E74 as LNB1 overload and E75 as LNB2 overload, and an overload code generally points at a short in a cable or connector rather than at a failed LNB. That is why we test the run before anyone is quoted for new hardware — see Smart LNB installation for what those codes mean at the dish end.
Why we make connectors up fresh
Reusing a connector that has been outdoors for years is a false economy. It still grips, so it looks fine, but the seal has gone and the metal underneath has been sitting in salt air. We fit new ones on any joint we open, because coming back for a connector is more expensive for everyone than fitting one properly the first time.
Wall points, plates and the part you actually see
A cable poking out of a hole in the skirting is not an installation, it is an unfinished job. It also fails sooner, because the cable takes strain every time somebody moves the unit, and there is nothing holding it but the connector on the back of the decoder.
A proper wall plate terminates the run in the wall, takes the strain there, and gives you a short flex from plate to decoder that can be replaced in seconds if it is damaged. It looks better, and it means the next person working on that television is not pulling on cable that runs into the roof.
- Plate fitted square, into a box, not screwed onto a broken piece of plaster
- Termination made off inside the box with enough slack to redo it once
- Position chosen for where the television will actually sit, including its height on a bracket
- Existing cable in the wall tested rather than assumed to be sound
Everything outdoors is a sealing job
Cape Town is hard on external connections. The wind moves anything not properly clipped, the sun degrades the outer sheath on the north-facing side of a house, and near the sea the salt gets into every joint that is not sealed. Water does not need much of an opening — once it is inside a connector it wicks along the cable and the corrosion spreads inwards from there.
So outdoor joints get sealed as a matter of course, cable is clipped at sensible intervals rather than left to swing, and we leave a drip loop before anything enters the building so water runs off instead of following the cable through the wall. In Table View and along the rest of the Blaauwberg coast, this is most of what decides whether an installation lasts three years or ten.
It is also why we would rather run a slightly longer route than take a shortcut across an exposed roof face. Cable that is protected from sun and wind will outlive cable that is not, regardless of what it cost.
Adding a point to a run that already exists
This is a common request and the answer depends on what the existing installation was built to carry. Signal is not infinite: split it enough times without accounting for it and every point gets weaker, which shows up as the odd screen struggling in poor weather while the others are fine.
We test what is there before adding to it. Sometimes there is plenty of headroom and a new point is straightforward. Sometimes the installation is already at its limit and the equipment at the dish end has to change first. Where several rooms are involved rather than one, the planning is worth doing as a whole — that is covered on multiroom installation.
One more thing worth saying: old aerial cable in the wall is not automatically usable. Plenty of Cape Town houses have coax from the analogue era running to lounge and bedroom points. Some of it is fine and some of it is not remotely suitable, and the only way to know is to test it. We do that before deciding to reuse it, because pulling new cable is cheaper than diagnosing a mystery fault on old cable for years afterwards.
Cabling as part of a bigger job
If a dish is going up at the same time, see dish installation. If you are planning cable routes in a house that is being built or renovated, new homes and renovations is the page you want.
Questions we get asked
Can you use the aerial cable already in my walls?
How long can a cable run be before it causes problems?
Is a wall plate really necessary, or is a cable through the skirting fine?
Water has got into the connection outside. Does the whole cable need replacing?
Why does wiggling the cable behind the decoder bring the picture back?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za