DStv · Cape Town
XtraView installation for a second decoder
XtraView puts a second decoder on the same subscription so a second room has its own picture. Most of the work is physical: a feed to the new point, power, and a cable route that does not spoil the house.

MultiChoice spells it XtraView. Enough people type it as Extra View that we should say so once, plainly, so you know you are on the right page — they are the same thing, and the search term is not wrong, just not DStv's spelling.
The idea is simple. One subscription, one household, more than one decoder, so the lounge and a bedroom are not negotiating over the same screen. The subscription side of the arrangement is between you and MultiChoice. Ours is the part with the ladder in it.
What the second decoder needs from the installation
Every decoder in the house needs four things, and none of them are optional.
- A satellite feed of its own, reaching that room from the LNB on the dish
- A power point close enough that nothing is running across a floor
- A connection to the television in that room
- Its own smartcard, seated properly in the slot
The first one is the whole job. A single decoder installation needs the dish to feed one point. Add a second decoder and the installation has to carry more than it did, which is a question about the LNB and the cabling rather than about either decoder. This is exactly the problem the Smart LNB exists to solve — MultiChoice recommends it for most XtraView installations in single-unit dwellings, because it offers a single cable solution for distributing multiple satellite signals rather than a bundle of separate runs.
In a complex or an apartment block that recommendation does not apply. MultiChoice states the Smart LNB is not suitable for Multiple Unit Dwellings, so a second point in a flat is a different conversation — usually one that starts with what the building's communal system was built to carry. We have set that out on DStv in complexes and apartments.
Getting the feed to the second room
This is where the job is either quick or interesting. A second point in the room directly below the roof entry is an afternoon. A second point in a downstairs bedroom at the far end of a face-brick double-storey with a concrete slab between the floors is not.
The usual routes
- Through the roof space and down an internal wall — the neatest result, and the first thing we look for
- Along a ceiling void or bulkhead where the roof space is inaccessible
- Behind skirting or in trunking where there is no route inside the wall
- Externally down a wall and back in through the window frame or a wall entry — the last resort, and done properly it should be almost invisible
We show you the route before we drill anything, and if the tidiest route is not the cheapest one to install, you get to make that decision rather than discovering it afterwards. The materials and terminations matter as much as the route; that side of it is on our cabling and TV points page.
Faults that show up on a linked pair
Two decoders on one installation give you one extra thing that can go wrong: the connection between them. DStv's error code list gives E73 as TV link overload. Where we see it, the first things we look at are the connectors and the cable on that link, because a short or a crushed cable produces exactly this sort of complaint.
The other pattern worth knowing is a fault that affects one decoder and not the other. That is useful information rather than a nuisance — if the lounge is fine and the bedroom is not, the dish is almost certainly innocent and the problem lies somewhere between the LNB output and that room. If both go down together, we start outside. Our signal problems page walks through the same logic in more detail.
One decoder is frozen, the other is fine
Before booking anything, switch the affected decoder off at the wall plug, wait at least ten seconds, and switch it on again. DStv gives that advice for its weather code and it is a reasonable first move for a decoder behaving oddly generally. If it comes back and stays back, you have saved yourself a call-out.
Where people put the second point
The main bedroom is the most common request, followed by a child's room, a study, a patio or braai area, and a granny flat or cottage. The last two are worth a mention because they change the job. An outbuilding means an external cable run, and external runs live or die on how the connections are sealed — in Milnerton or anywhere else with salt in the air, that is the part that decides whether the installation lasts.
If you are adding several points rather than one, it stops being an XtraView question and becomes a layout question. Our page on multiroom installation deals with houses where three or four rooms want a picture and the cabling has to be planned as a whole.
What we survey before quoting a second point
Adding a decoder to an installation that already works is not a fixed job with a fixed answer, because the answer depends entirely on what is already on the property. We would rather spend twenty minutes looking than guess, so a survey comes first.
- The LNB on the dish, and how many feeds it can actually carry
- The existing cable — its type, its condition, and whether it was run where anyone can still get at it
- Every connector we can reach, because that is where old installations fail first
- The route to the new room, and whether the roof space is accessible from inside
- In a complex, who owns the dish and what the rules are about touching it
Two outcomes come out of that. Either the existing installation has room in it and the work is a run of cable and a new point, or the installation is already at its limit and the LNB has to change before anything else happens. Both are normal. What is not normal, and what we will not do, is hang a second decoder off an installation that cannot support it and let you discover the problem a fortnight later when the weather turns.
Starting from scratch?
If there is no dish on the property yet, the second decoder should be planned into the first installation rather than bolted on later — it usually costs less work overall. See DStv installation in Cape Town and dish installation for how we set a property up from nothing.
Questions we get asked
Does the second decoder need its own dish?
Can the second decoder go in a cottage or flatlet on the same property?
Do both decoders need their own smartcard?
My bedroom decoder has no signal but the lounge one is working. What does that tell you?
Can you add a second decoder to an installation somebody else put in?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za