DStv · Cape Town
No signal on DStv, and what the error is telling you
E48 and E48-32 are not the same message and they do not point at the same fault. This page explains the difference, gives DStv's own first two checks, and sets out what is usually stopping the signal once those have failed.

A decoder that cannot see the satellite says so in a specific way, and the code on the screen is more useful than most people realise. It will not tell you which part has failed, but it does tell you which half of the problem you are in - and it distinguishes between a system that is struggling in bad weather and one that has genuinely stopped working.
E48 and E48-32 are two different messages
On DStv's official error code list, E48 is "Searching for Signal". That is the general message: the decoder is not receiving what it expects, and the reason could be the dish, the cable, the LNB or the weather. It is a symptom, not a diagnosis.
E48-32 is the weather variant. DStv attributes it to stormy weather and rain, and the reason that distinction matters is diagnostic. A system that fails during a front and recovers cleanly afterwards is behaving the way satellite reception behaves in heavy rain. A system that shows E48 in perfect weather and never comes back has a physical fault, and no amount of waiting will help it.
The awkward middle case is the one worth paying attention to: an installation that used to shrug off rain and now drops out in every shower. That is not weather. That is a marginal installation - usually a connector taking on water or an aim that has drifted - which the weather is now exposing.
The two checks DStv asks you to do first
DStv's own guidance for E48-32 is two steps, and they are worth doing before anyone books a technician, because between them they resolve a fair number of calls.
Check that the cables from the dish are connected to the decoder properly
DStv's wording is to check that the cables from the satellite dish are connected to the decoder properly. In practice that means the connector at the back of the decoder, which gets nudged loose when a unit is moved for cleaning or when something is plugged in behind the cabinet. Hand tight is enough - it should not spin freely.
Switch the decoder off at the wall plug and wait at least ten seconds
DStv asks you to switch off the decoder power at the wall plug and wait at least 10 seconds before switching it on again. The waiting is the part people skip, and it is the part that matters. Standby is not off, so use the wall switch rather than the remote, and give it the full ten seconds before you power it back up.
While you are waiting for a signal to come back in bad weather, DStv also points customers at DStv Stream, BoxOffice and Showmax as alternatives.
If both of those steps have been done properly and the message is still there in clear weather, the fault is physical and it is somewhere between the LNB and the decoder.
What is actually stopping the signal
The aim has drifted
A dish does not need to move far to stop working. Wind over years, a bracket bolt slowly working loose, or a single knock from a ladder during gutter cleaning is enough. The signature is gradual: pixelation first, then breaking up on bad days, then nothing. Dish alignment covers what putting that right involves.
The LNB has failed
The part on the end of the arm is powered and permanently outdoors, and it does fail. It tends to fail progressively rather than all at once, and heat often makes it worse, so a system that works in the morning and struggles by mid-afternoon is a reasonable suspect.
Water has got into a connector
The single most common physical cause we find. The connector at the dish end faces the weather, and once moisture is inside it, corrosion does the rest. It is cheap to fix and easy to miss from the ground, and it accounts for a large share of the "the dish must be broken" calls we take.
The cable is damaged
Perished sheathing after years of sun, a run crushed flat by staples, chafing where the cable crosses a gutter or a roof edge, or rodent damage in a ceiling. Any of those will drop the signal, and all of them are invisible until somebody follows the run properly.
Something has grown into the line of sight
This one catches people out because nothing at the house changed. A tree in your garden or the neighbour's puts on a few years of growth, a second storey goes up next door, or a palm that was below the dish is now level with it. The dish needs a clear line of sight to the north-east, and once something is standing in it, aiming will not help - the dish has to move. Dish installation and mounting explains how a position gets chosen with that in mind.
Signal-related error codes
| Code | What DStv calls it | Where we start |
|---|---|---|
| E48 | Searching for Signal | Anywhere between dish and decoder - alignment, cable, LNB or weather |
| E48-32 | Weather | DStv's weather variant. Do the two checks above; if it persists in clear weather, treat it as a physical fault |
| E73 | TV link overload | The cabling on that run rather than the dish |
| E74 | LNB1 overload | In our experience, a cable or connector short rather than the dish itself |
| E75 | LNB2 overload | Same as E74 - we trace the run and the connectors on that output |
Two others turn up alongside signal complaints. On DStv's list, E50 is "No Services Available" and E72 is "Rescan in progress" - the second is the decoder doing something rather than failing at something, so give it time to finish before you decide anything is wrong.
Codes about smartcards, subscriptions and channels are a different family altogether and are covered on decoder and smartcard errors. If the message you are looking at mentions a card or a subscription, that page is the one you want.
When it only goes wrong in wind or rain
Intermittent faults are the ones people live with for months, and they are the most diagnosable of all. A fault that appears in wind and clears in still weather is mechanical - a bracket that flexes, a dish that moves on a loose clamp, a cable that gets tugged. A fault that appears in rain and clears when things dry out is water - almost always a connector, occasionally a cracked cable sheath.
Neither of those gets better on its own. Water in a connector corrodes a little more with every front, and a bracket that has started to move keeps moving. Both are inexpensive while they are still intermittent and considerably less so once the connector has destroyed itself, which is the argument for dealing with it in autumn rather than in August. DStv repairs is where that work sits.
If the whole system is being moved
Signal problems that start the week after a move are usually about the new position rather than about the hardware. DStv relocation covers remounting and aiming at a new address, and the installation hub explains how the pieces fit together.
Questions we get asked
What is the difference between E48 and E48-32?
My DStv goes off every time it rains now, and it never used to. Is that just the weather?
How long should I leave the decoder switched off at the wall?
Can a tree really block a satellite signal?
Nothing at my house has changed, so why has the signal gone?
Should I try adjusting the dish myself?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za