Advice

OpenView from the outside in: dish, decoder, and no monthly bill

OpenView is satellite television with no monthly subscription fee. That one difference changes how the whole system behaves, including what can go wrong with it and who you phone when it does.

Satellite dish on a suburban wall with an OpenView decoder connected to a television indoors

Most explanations of OpenView are written by someone trying to sell you something, which is a poor way to understand how it actually works. We install and repair it and we have no stake in which service you choose, so this is the mechanical version: what the parts are, what each one does, and where the money goes given that it does not go out monthly.

Free-to-air, and what that phrase actually describes

Free-to-air means the signal is broadcast without being locked to a paying account. A subscription service scrambles what it sends and the decoder unscrambles it only while the account is in good standing, which is why a lapsed DStv subscription puts an error on the screen while the dish outside carries on receiving perfectly well.

OpenView does not work that way. The channels come down and the decoder shows them. OpenView's own description of the service is "over 20 TV and radio channels", and the line-up includes SABC channels and e.tv. We are not going to print an exact number on this page, because line-ups change and a number typed into a web page does not. If a particular channel is the reason you are considering this, check the current list on OpenView's own site before spending anything.

The practical consequence is that there is nothing to lapse, nothing to reconnect and no account state that can put an error on your screen. It also means that when a picture does disappear, the cause is always physical. That narrows fault-finding considerably, which is the subject of OpenView signal problems.

Where the money goes, since it does not go monthly

You pay once, for equipment and for the work of putting it in. After that the running cost is the electricity the decoder uses and nothing else.

What that once-off figure covers depends almost entirely on what is already on your property. A house with a working dish, a sound bracket, a healthy LNB and a cable already run through the wall needs a decoder and an hour or two. A house with nothing needs all of it. Between those two extremes sits most of what we actually see: a dish that is fine and connectors that are not, or a good installation aimed at nothing in particular because it has been standing unused for three years.

This is why we ask people not to take an old dish down before someone has looked at it. The bracket, fixed into something that will hold it, is most of the value of the old installation. Everything else on the arm can be replaced individually. Our page on dish installation and alignment covers what that assessment involves.

The four things that have to exist for a picture

Every satellite installation, whichever service is behind it, is the same four parts in the same order.

  • A dish, aimed with a clear line of sight to the north-east, which reflects the signal to a single point.
  • An LNB on the arm, which is the part that actually receives and converts, and the part most likely to fail outdoors.
  • A cable run from the LNB into the house, terminated with connectors that keep water out.
  • A decoder, which turns what arrives into a picture on a television.

If you want the physics rather than the list, our article on how satellite dishes actually work goes through why the aim has to be far more precise than it looks and why the dish itself receives nothing.

The reason this matters for OpenView specifically is the north-east requirement. OpenView's own material states that the decoder connects to an existing satellite dish pointing north-east. A household that has cancelled a subscription service usually has exactly that on the wall already, which is why switching is often a much smaller job than people expect.

The OV512, and the two ways content reaches it

The decoder named on OpenView's site is the OV512, identified there as model OV512 (KSTB6168) and described as Wi-Fi capable. It sits between the cable from the dish and your television, and it is the only box in the system.

Content reaches it by two separate paths. The satellite channels come down the dish feed and need no internet at all: the decoder works perfectly in a house with no Wi-Fi and no router. Separately, OpenView says the built-in Wi-Fi receiver provides access to additional on-demand content, and describes being able to fast forward, pause and rewind that Wi-Fi content and catch up on episodes of local favourites. OpenView's own page carries a footnote on this that is worth repeating plainly: data costs apply. The on-demand side uses your internet connection like any other streaming, and it is charged for by whoever supplies that connection.

So the honest summary is two systems in one box. The satellite half is free to run once installed. The internet half costs whatever your data costs. Setting the decoder up on a home network is part of a normal installation and is covered on our OV512 installation page, along with what to do when the router is at one end of the house and the television at the other.

How it behaves when something goes wrong

Because there is no subscription in the picture, an OpenView fault is always one of five things: the dish, the LNB, the cable, a connector, or the decoder. That is a short list and it can be worked through in order.

The pattern of the failure tells you where to look. Everything gone at once, permanently, usually means the LNB, the cable or an aim that has been lost. A picture that breaks up in the wind and recovers points at a mounting that is no longer rigid or an aim with no margin left. A few channels missing while the rest are fine is rarely a dish problem at all. A decoder that runs, gets hot and switches itself off is the box, and OV512 faults covers what is worth repairing and what is not.

One thing that catches people out is a dish that stood unused for years before being pressed back into service. It may work on the day it is connected and be marginal from the start, because nobody re-aimed it and the connectors have had three winters of weather. That installation will fail on the first hard south-easter, and it was never really working.

Who OpenView actually suits

Households whose viewing is mostly news, local channels and general entertainment tend to switch and never think about it again. Households built around a specific sports competition or a particular series on a particular channel need to check that it is there rather than assuming, because OpenView is a different service with a different line-up and not a discounted version of the same one.

The other group it suits well is the second television. Plenty of Cape Town homes keep a subscription on the main set and put OpenView in the flatlet, the spare room or the cottage, where the viewing is a few hours a week. With no monthly fee on that side, the second box costs nothing to keep once it is in. If you are weighing the two against each other properly, the comparison article sets out the trade-off, and our OpenView installation page covers the work itself.

Questions we get asked

Is OpenView the same as the free channels I used to get with an aerial?
No. Those came off a terrestrial aerial on the roof, while OpenView arrives by satellite and needs a dish aimed at the north-east. What they have in common is that neither carries a monthly subscription. The equipment, the installation and the line-up are all different.
Does OpenView use my internet data?
The satellite channels do not, and they work in a house with no internet at all. The additional on-demand content the OV512 offers over Wi-Fi does use your connection, and OpenView's own page notes that data costs apply to it. So the answer depends entirely on which half of the box you are using.
Can one OV512 serve two televisions in the same house?
One decoder produces one picture, so a second television connected to the same box shows the same channel at the same time. If two rooms want to watch different things, that means a second decoder, and usually a second feed from the dish. It is worth deciding this before the cable is run rather than after.
What happens to OpenView during load-shedding?
Nothing that lasts. The decoder loses power and comes back when the power does, sometimes taking a few minutes to settle on a channel. Repeated hard power cuts are harder on the decoder's power supply than on anything else in the system, which is worth knowing if the box has started behaving oddly after a bad month.
Do the channels ever change, and would I have to do anything?
Line-ups are not fixed and do move over time. If something you watch disappears, a rescan on the decoder is the sensible first response before assuming a fault, because it rebuilds the channel list from what is actually being broadcast. Check the current line-up on OpenView's own site rather than any third-party page, this one included.
If nothing is billed monthly, is there anything that can lapse?
No, and that is the practical difference from a subscription service. There is no account state that can put a message on your screen and no reconnection to arrange after a break. Anything that stops working is a physical fault in the dish, the LNB, the cable, a connector or the decoder.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za