Southern Suburbs · Lansdowne
OpenView in Lansdowne, and what it costs to run
Lansdowne households often have more televisions than decoders. OpenView is free-to-air satellite with no monthly subscription fee once the equipment is yours, which changes the arithmetic on the second and third set.

Plenty of houses in Lansdowne are running more than one decoder already, usually because the household has grown into the building. A room was added, the children want their own set, and each new point has been another line on the monthly bill. OpenView changes that calculation, because there is no monthly subscription fee at all once you own the equipment.
We install and repair OpenView across the southern suburbs and the flats as an independent business, unconnected to OpenView or to MultiChoice. This page covers what the service does in a Lansdowne house, and the two things about the suburb that genuinely change the job: the wind and the distance between buildings.
An extra set without an extra monthly bill
The usual shape of an OpenView job here is not a household leaving satellite television behind. It is a household keeping what it has on the main television and putting a free-to-air box on the rooms that do not justify a subscription point. Once it is installed, that box costs the electricity it uses and nothing else.
It works the other way as well. Where a household is cutting back rather than adding, the decoder that has been showing a subscription message since the account lapsed is not the end of the story, because the dish outside is still perfectly good. Our DStv installation page for Lansdowne covers the subscription side of the same roof if you are weighing the two up.
What we will not do is pretend the two services are interchangeable. OpenView's own claim is over 20 TV and radio channels, including SABC channels and e.tv, and that line-up is not a discounted version of a subscription package. Households whose viewing is mostly local channels, news and general entertainment tend to switch and not think about it again. Households built around one particular competition should check the current list on OpenView's own site first.
Wind across the flats works on the mounting first
Lansdowne is exposed, and the south-easter has been working on every dish in the suburb for as long as it has been up there. A reused dish is therefore a mounting question before it is an electronics question. Clamp bolts give up a fraction at a time, and a dish that has drifted does not look as though it has moved.
So we check what is holding the dish before touching the aim, because aiming a dish that still moves is work you pay for twice. Where the fixings are sound, bringing the aim back is a short job done on a meter and confirmed at the decoder. Where they are not, the honest answer is a remount first.
- Fixings into solid material rather than plaster, hollow block or a fascia board
- Clamp bolts checked and re-tightened before any aiming is attempted
- The aim set on a meter, then confirmed again once everything is locked down
- Cable clipped at sensible intervals so wind cannot work at the connector ends
Getting a feed to an added room between close-set houses
Added rooms are the reason for a good share of the second points we fit here, and the constraint is the space between buildings rather than the length of the run. The cable has to reach the new room without crossing a neighbour's property or hanging over an open yard, which usually means an external run clipped along your own wall and sealed where it enters the building.
On a semi it is worth agreeing where fixings and cable runs go before anything is drilled, and we keep both on your side of the boundary even where the shorter route is over the other. That is a short conversation at the survey and an awkward one afterwards.
Where several points are likely, it is better to plan them together than to add one a year, because every point takes a share of what the installation delivers. Dish installation and alignment for OpenView explains what the outdoor side has to be delivering before any of that is worth doing.
Before you commit, check the line-up rather than our word for it
The decoder named on OpenView's site is the OV512, and beyond the satellite channels it offers additional on-demand content over Wi-Fi. In a busy house that is worth knowing about, because it means the box wants a position your router reaches. The satellite side is entirely independent of that and works in a house with no internet at all.
Everything else about the decision is arithmetic you can do yourself. There is no monthly fee, there is a once-off cost for equipment and installation, and the channel line-up is published by OpenView. Where we are useful is the part on the roof and the cable between there and the television. Signal problems on OpenView covers what goes wrong afterwards and how it is diagnosed, and the broader OpenView installation page sets out how a job is scoped.
When it is the set and not the signal
A signal fault takes out every television fed by that decoder at once. A set that will not switch on, or that has sound and no picture, is a television fault and belongs on TV repairs in Lansdowne. Working out which one you have saves booking the wrong visit.
Questions we get asked in Lansdowne
We already run several decoders in this house. Where does OpenView fit in?
Does an OpenView box need its own dish if the house already has one?
Our dish shakes in a strong south-easter. Will OpenView be worse than what we have?
The back room was added on and has no ceiling void. Can it still get a feed?
If we drop the subscription completely, what are we giving up?
Can the same dish carry a subscription decoder and an OV512 at the same time?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za