Southern Suburbs · Ottery

OpenView installation and setup in Ottery

Ottery has open ground and few obstructions, so a dish here usually has the north-east view it needs. That makes OpenView a straightforward job and it also narrows down where a fault can be hiding.

Installer checking a satellite cable connection on the outside wall of an Ottery house

OpenView is free-to-air satellite television. There is no monthly subscription fee once you own the equipment, the decoder named on the official site is the OV512, and the service connects to an existing satellite dish pointing north-east. In Ottery that last point is more useful than usual, because there is a lot of redundant satellite hardware sitting on walls here doing nothing.

We work across Ottery on houses and on the smaller commercial premises mixed in among them. We are an independent installer with no connection to OpenView or MultiChoice, so nothing on this page is a sales pitch for one service over another.

Open ground, clear sight lines and where the fault actually sits

The line of sight question that dominates work in denser suburbs mostly does not arise here. Ground is open, buildings are not stacked against each other, and a dish can generally see north-east from whichever wall suits the house. That is genuinely good news, and it has a second effect people do not expect.

When the view is clear and the picture is still poor, the list of possible causes gets short. It is the aim, the mounting, the LNB, a connector or the cable, and none of those is guesswork once somebody has a meter on the line. Wind across open ground is the usual reason the aim has drifted, since there is nothing between a dish here and the weather.

That is also why we test rather than replace parts in order. Swapping an LNB because it is the easiest thing to reach is how people end up paying twice for a fault that was in a connector. No signal and weak signal on OpenView sets out how the pattern of a fault narrows it down before anybody gets on a roof.

Taking the dish with you when you move within Ottery

A fair number of the households we see here have moved once or twice inside the same few streets, and the dish has come along. Where it has been taken down carefully it is worth putting back up, and where it has spent a year in a garage it is worth testing before it goes anywhere near a wall.

Two things go wrong with a stored dish. The reflector gets leaned on and takes a knock that stops it focusing properly, which is not always obvious to look at. The connectors, having been cut off and remade in a hurry, are a common source of a picture that works and then does not. Both are cheap to sort out at the time and irritating to chase afterwards.

If the new address already has a dish on the wall, that changes the job again and usually for the better. Dish installation and alignment for OpenView covers recommissioning an existing dish, and our DStv installation page for Ottery covers the same ground for a household staying on a subscription.

A screen on small premises, with nothing to pay each month

The light industrial side of Ottery brings a different kind of call: a screen in a workshop office, a reception area or a staff room, where nobody wants a monthly account for something that is on in the background. Free-to-air suits that, and the installation is not fundamentally different from a house.

What does change is the building. Steel roofs and industrial walls need fixings specified for what they are going into, cable runs tend to be longer, and the route usually has to keep out of the way of everything else happening in the building. Those are all decided on site rather than over the phone.

  • A mounting fixed into structure rather than into sheeting or cladding
  • A cable route that stays out of the working area and is protected where it cannot
  • Sealed entries wherever the run passes through the building envelope
  • The decoder somewhere with air around it and not shut in a cupboard

What the OV512 needs from your television and your network

Indoors the job is short. The decoder connects to the television, the channels are scanned in, and we check the signal at the decoder itself rather than treating the reading outside as the last word. Then we leave it running a while, because a marginal installation looks perfect for the first two minutes.

The OV512 also offers additional on-demand content over Wi-Fi, so if you want that side of it we put the box on your network and check the connection holds where the television actually stands. In a workshop with a router at the far end of the building, that is worth finding out on the day. None of it affects the satellite channels, which do not need the internet.

On the channels themselves, OpenView says over 20 TV and radio channels, including SABC channels and e.tv. We do not publish a precise number because line-ups change. Our OpenView installation page goes through the decision in more detail, including how the service compares with a subscription.

Questions we get asked in Ottery

Nothing blocks our dish here, so why would OpenView give a weak picture?
A clear view is only one of the requirements. The aim, the mounting, the LNB, the connectors and the cable all have to be right as well, and wind across open ground is very good at moving a dish that was not fixed into something solid. A clear line of sight simply means the fault is one of the others.
We are moving a few streets away. Is the dish worth taking?
Usually yes, if it comes down carefully and the reflector is not bent in the process. Check what is at the new address first, though, since a dish already on that wall may save the job entirely. Either way the connectors get remade rather than reused.
Can OpenView go into the office at the back of a workshop?
Yes. The work is the same in principle, with the difference in the building rather than the service. Fixings have to suit a steel or industrial structure, the cable route needs protecting, and the run is usually longer than in a house.
The dish has been in the garage since the building work. Can it go straight back up?
It can go back up, but not straight. A stored dish gets leaned on, and a reflector that has been knocked out of shape will not focus properly no matter how carefully it is aimed. We check the shape and remake the connectors before mounting it.
The set in the workshop is an old one. Will the decoder work with it?
That depends on what inputs the television has, which is worth establishing before anything is bought. Tell us the make and model when you book and we can say what is needed to connect the two.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za