Advice

Moving house with DStv: a checklist in the order things actually happen

A move is the one time a satellite installation gets taken apart and put back together by people who did not build it. Working through it in order costs nothing and prevents most of the calls we get in the fortnight after moving day.

Packed moving boxes in an empty lounge with a satellite decoder on top of one of them

The pattern is familiar. The move goes well, everything else in the house works, and on the third evening somebody discovers that there is a dish outside and a decoder inside and nothing at all in between. By then the removal company has gone, the old address is somebody else's, and the useful information about how the previous installation was put together has been thrown away.

None of that is difficult to avoid. What follows is ordered by when it happens rather than by category, because that is how a move actually unfolds.

Two weeks out: decisions, not technicians

The first questions are yours to answer and none of them need anyone on a ladder.

  • Are you taking the dish, or leaving it? A dish that is old, corroded or bolted into something you would rather not disturb is usually not worth transporting.
  • How many rooms need a picture at the new house, and which ones? This decides the whole cabling job and it is cheaper to answer now than to add a room later.
  • Is the new place a house, a flat or a unit in a complex? That changes who has to give permission before anything is drilled.
  • Does anyone in the household need a working picture on the first night, or can it wait a few days? Say so when you book, because it changes the order of the work.
  • Is there an existing dish at the new address, and does anyone know whether it works?

Our page on DStv relocation goes into the removal and remounting side in detail. The point of doing this early is that a booking made two weeks ahead can be scheduled around the move, while one made on moving day competes with everyone else who forgot.

The walk-through: what to look for at the new address

You will almost certainly visit the new place before you move in, for a snagging inspection or to hand over keys. Ten minutes spent looking at the right things then is worth more than any amount of guessing afterwards.

  1. Find the dish, if there is one

    Look at the walls and the roof edge on the side of the property facing north-east, which is the direction a satellite dish has to look in South Africa. Photograph it from the ground, including the bracket and where the cable disappears into the wall. Nobody expects you to judge its condition, only to record that it exists and where.

  2. Count the wall plates inside

    Walk each room and look behind where a television would stand, low down on the skirting. A round socket with a threaded centre is a satellite point. Note which rooms have one and which do not, because that is exactly the list a quote is built from.

  3. Look at the route the cable would have to take

    If a room has no point, look at whether there is a ceiling, a skirting run or an external wall that a cable could follow. A room on the far side of the house from the dish is not a problem, but it is a longer job than the one next door.

  4. Check the view to the north-east

    Stand where the dish is or would be and look for trees, a new neighbouring wall or a higher building in that direction. A dish needs a clear line of sight and a large tree in the way is not something that can be worked around from the ground.

  5. Note the plug points

    A decoder needs a socket near the television, and a house full of extension leads on moving day is how equipment gets knocked over. Worth knowing before the furniture arrives.

Packing day: what actually travels with you

The decoder, its remote, its power supply and its smartcard if it has one. Those go in the car, not in the van, and they go in a box you can identify without opening six others. Decoders are not heavy but they are fragile, and a box that has had a wardrobe put on it is a box with a problem inside.

Photograph the back of the decoder before you unplug anything. Every cable in place, well lit, close enough to read the labels on the sockets. It takes fifteen seconds and it removes all argument about what went where. Do the same for the back of the television if a soundbar or console is involved.

If the dish is coming, it should be taken down properly rather than wrenched off, and the LNB on the arm should be wrapped rather than left to knock about in a bakkie. The bracket bolts are worth keeping in a labelled bag. Whether it is worth taking at all is covered on the relocation page, and the honest answer is often no.

The five-minute photograph list

  • The back of the decoder with everything plugged in
  • The wall plate and the cable behind the television
  • The dish on the wall, from the ground, including the bracket
  • The model and serial number on the underside of the decoder
  • The back of the television if anything else is connected to it

The first evening in the new house

Connect the decoder, switch on and see what the screen says before assuming anything. There are only a few outcomes and each one points somewhere specific.

A picture straight away means the existing installation at the new address is live and aimed, and you are finished. A signal error means the box is fine and something outside is not: no dish, a dish that is not aimed at anything, a cable that goes nowhere, or a connector that has been sitting open to the weather. A subscription error is not a technical matter at all, and no work on the roof will change it. Our article on what to check before you phone anyone sorts those categories out in about ten minutes.

Do not spend the first night rearranging the dish. It is dark, you do not know the roof, and a dish that is nearly right can be made much worse by an enthusiastic nudge. Note the code, note whether every room is affected or only one, and leave it.

The first week, and the faults that surface then

Some problems only appear once the house is being lived in, and they have a characteristic look.

A picture that works in the day and breaks up in the evening, or that goes when the wind comes up, points at an installation with very little margin rather than one that is broken. That often means a dish that was aimed adequately years ago and has drifted, which is what realignment exists to correct, or connectors outside that have taken years of weather. Cape Town's wind and salt air are hard on both.

One room working and another not is a downstream problem: the cable, the plate or that decoder. Every room failing at once is upstream, at the dish or the cable coming down from it. That single test tells a technician more than any description of the symptom, and it costs you a walk down the passage.

In a flat or a complex, a further possibility is that the communal system simply does not reach your unit, or reaches it through equipment that belongs to the body corporate rather than to you. That is a different conversation with different permissions, and what to know about DStv in complexes covers who decides what before you commit to anything.

The checklist in one place

  • Decide what is coming with you and what is staying, two weeks out
  • Book the work at the new address before moving week, not during it
  • Photograph the back of the decoder, the wall plate and the dish before anything moves
  • Walk the new property and note dish, wall plates, cable routes and the view north-east
  • Carry the decoder, remote, power supply and smartcard in the car
  • Confirm permissions in writing if the new place is a flat or a complex
  • On the first evening, read the screen rather than climbing anything
  • Report what changed and when, not just that it is not working

Questions we get asked

How far ahead should I book the installation at the new address?
Before moving week if you possibly can. A booking made in advance can be arranged around the day the furniture arrives, while one made on the day itself has to fit wherever there is space. It also gives you time to sort out permission if the new place turns out to need it.
What should I photograph before anything is unplugged?
The back of the decoder with every cable still in place, the wall plate behind the television, and the dish from the ground including its bracket. Add the model and serial number from underneath the decoder. Those five pictures answer most of the questions that come up later.
There is a dish outside but no wall plate anywhere inside. What does that mean?
Usually that the cable was run to one spot and terminated behind furniture, or that it was removed when the previous owner left. It is worth looking low down on the skirting in the main bedroom and the lounge before concluding there is nothing. If there genuinely is no cable indoors, the dish may still be perfectly good and only the inside work needs doing.
Should the decoder travel in the moving van or in the car?
In the car, with the remote and the power supply, in a box you can find without opening others. Decoders are light enough to end up near the top of a load and fragile enough to mind about what gets stacked on them. It also means you can test the new house on the first evening rather than the third.
We are renting. What can we put up and what needs permission?
Anything that involves drilling into a wall, a roof or a common area needs the landlord's agreement, and in a complex it usually needs the body corporate as well. Get it in writing before the day rather than on it. Reusing an existing dish and cable rarely raises the same questions, which is one reason it is worth checking what is already there.
Everything is connected and there is still no picture on the first night. What do we check?
Read the code on the screen and write it down exactly, including anything after a hyphen. Then check whether every room is affected or only one. Those two answers separate a subscription matter from a dish problem from a cable problem, and they cost nothing to establish before anyone travels.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za