West Coast & Blaauwberg · Century City

DStv installation and fault-finding in Century City apartments

Century City is apartments and cluster developments almost end to end, and nearly all of it runs on communal satellite systems. That single fact changes the diagnosis: when the picture goes here, the dish is rarely the thing that has failed.

Satellite distribution equipment in the service cupboard of an apartment building

We do very little dish work in Century City, and that is not because there is nothing wrong. It is because the equipment that usually fails in a freestanding house is not the equipment serving your flat. In a managed building the dish is bolted to a roof, feeding dozens of units through a distribution system, and it is the distribution that ages, not the reflector.

Start from the assumption that the system is communal

In most Century City buildings the satellite signal arrives at a wall point in your unit and everything behind that plate belongs to the building. You own the decoder and the flex between it and the plate. That is a short list, and it is worth knowing exactly how short before you pay anyone to investigate.

It also means the first useful test costs nothing: ask a neighbour, ideally one in the same stack, whether they have a picture right now. If several units are affected, the problem is in shared equipment and the managing agent has to act, not you. Our page on DStv in complexes and apartments explains why a communal dish so seldom turns out to be the culprit and how ownership is divided.

What is worth checking inside your own unit

If yours is the only flat affected, the fault is almost certainly on your side of the plate, and that is straightforward work.

  • The flex from the wall plate to the decoder, and both connectors on it, which are the single most common failure in a flat
  • Whether the plate itself has been knocked loose or disconnected during past work, painting or a kitchen refit
  • Whether the decoder is showing E48, which means it is searching for signal, or one of the busy messages such as E30, E32, E72 or E120, which mean it is checking, validating, rescanning or synchronising and needs to be left alone
  • Whether a second decoder or a splitter has been added somewhere in the flat, since that changes what reaches each point

That is the sequence we work through when we attend, and it is usually finished quickly. Decoder problems and error codes goes through the messages in detail, and signal problems covers what the E48 family is actually telling you.

Why a Smart LNB is the wrong answer in a block

This comes up in Century City more than anywhere else we work, because so many residents here are quoted for hardware that belongs on a house. MultiChoice recommends the DStv Smart LNB for all DStv Explora and most XtraView installations in single-unit dwellings, and states plainly that it is not suitable for Multiple Unit Dwellings. A block of flats is a multiple unit dwelling.

So if somebody has quoted you a Smart LNB for an apartment here, the question to ask is what problem it is meant to solve. In a building on a communal head end it will not address a distribution fault, and it is not what MultiChoice's own guidance points to. Our Smart LNB page sets out the two models MultiChoice names and what each one carries, so you can see the recommendation for yourself.

Roof access, managing agents and external fittings

Century City buildings are managed rather than informal, and that is mostly good news: there is someone whose job it is to deal with the shared system. It also means roof access is controlled, external fittings are strictly governed, and nothing gets fixed to a facade or a balcony on a resident's say-so.

Where a body corporate or managing agent wants the whole distribution looked at rather than one flat, we would rather deal with them directly, because the scope of that work is a building decision. Where an individual dish is permitted and a position exists, the wind is a real consideration here: it funnels hard between the blocks, so a mounting on an exposed elevation needs to be built for it, much as we do in Table View. The neighbouring block is also the usual obstruction, and a position that has a clear view to the north-east on a high floor may see nothing but wall from a low one.

Cable, wall plates and second points inside the flat

The apartments here are finished to a standard where visible trunking down a lounge wall is not acceptable, and we work to that. Cable is routed in existing ducts, ceiling voids and skirting where possible, and terminated on a proper wall plate rather than a bare cable poking through a hole. Adding a point to a bedroom is usually possible; how neatly it can be done depends entirely on what routes the building gives us, and we would rather look first and tell you honestly than promise an invisible run and then chase a wall.

Where you want a second decoder, the feed to the second room is the part that needs planning rather than the decoder itself, which our page on XtraView installation covers. In an apartment the useful question is not which decoder, but which route the cable can take to the second room.

Questions we get asked in Century City

Do I speak to the managing agent first, or call a technician?
Ask a neighbour in the same stack whether they have a picture, and let that decide. If several units are affected, it is the building's distribution and the managing agent has to act. If it is only your flat, the fault is on your side of the wall plate and that is work we can do.
My decoder shows E48 and my neighbours are watching television. Where does that put the fault?
On your side of the wall plate, in almost every case. E48 means the decoder is searching for signal, and if the shared system is delivering to everyone else, then the break is between the plate and your decoder, or in the plate itself. That is a small job and we can do it.
Our flat was renovated and the satellite point disappeared. Can it be brought back?
Usually. In most cases the run to the unit is still in the riser and the plate was capped, covered or plastered over rather than removed. We trace it and re-terminate on a new plate. If the run itself was cut during the work, the replacement has to follow the building's own route, and that involves management rather than just you.
The picture breaks up when the wind gets up between the buildings. Is that even possible on a communal system?
Yes, if the wind is moving something. Wind funnels hard between these blocks, and a dish or a cable run on an exposed roof position can move enough to matter. It is not the wind interfering with the signal itself, it is the wind moving equipment that should be rigid.
Can a second point be added in a flat where the cable is concealed?
Usually, but the route decides how neat it will be. We use existing ducts and ceiling voids where they exist and terminate on a wall plate. Where there is no route at all, the choice is between a visible run done tidily and no second point, and we would rather show you that on site than surprise you.
There is no satellite point in our unit at all. What are the options?
First establish whether the building has a system that simply was never brought into your unit, which is common in converted or altered flats. If it has, the fix is a connection to the existing distribution and that goes through building management. If it genuinely has none, the question becomes whether the scheme allows an individual dish and whether a position with a clear north-east view exists.

Get it sorted

Book a technician

Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.

218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za