Advice
Getting more signal out of the dish you already have
Most weak-signal complaints are fixed by an hour of careful work on hardware that is already on the wall. Very few of them are fixed by buying something new, and a bigger dish is almost never the answer.

A weak satellite signal announces itself in ways that are easy to live with for months. The picture blocks up for a second or two during a film. A channel is fine in the morning and unwatchable by late afternoon. Rain that never used to matter now takes the sport out. None of it is dramatic enough to phone about, so it gets tolerated until it stops being tolerable.
There is a real order of operations for fixing that, and it does not start with a shopping list. Almost everything that genuinely improves a satellite signal is an adjustment or a replacement of something that has degraded, not an addition.
The one adjustment that beats all the others
Aim comes first, every time, because it has more effect than everything else on this page combined. A dish concentrates signal from its whole surface onto a single small point where the LNB sits. That only works if the dish is pointing at the satellite accurately. Miss by a very small amount and the concentration is imperfect, and the amount arriving at the LNB drops away quickly.
The hard part is that a dish which is slightly off looks exactly like a dish which is spot on. There is nothing to see from the ground, no obvious tilt, no rattle. It is why aim can only sensibly be set with a meter on the LNB output while somebody moves the dish in very small increments and watches the reading, which is the whole substance of dish alignment work. Eyeballing it against the neighbour's dish gets you close enough to receive something and nowhere near close enough to receive everything.
Aim also has to be locked down properly once it is found. A perfect reading that the wind can walk off the satellite over the following winter is not an improvement, it is a delay.
A clear view to the north-east, and what quietly gets in the way
In South Africa the dish looks north-east, and it needs an unobstructed path in that direction. Not a mostly clear path. Satellite signal does not go round things and it does not go through much.
What catches people out is that the obstruction usually was not there when the dish went up. A tree that cleared the sight line by two metres in 2016 is now standing in it. A neighbour has added a storey. A palisade fence has been replaced with a solid wall, or a carport roof has been extended. In all of those cases the installation was correct on the day it was done and is wrong now, and no amount of adjustment at the dish will see through a trunk.
The fix here is position rather than aim: the dish moves to a wall, a pole or a roof section that still has the view. That is more work than a realignment and it usually means new cable, which is why it gets treated as a dish installation job rather than a service call.
Connectors are where most lost signal actually goes
If you could only inspect one thing on a satellite installation, inspect the connector at the LNB. It lives outdoors, it faces the weather, and it is the single most common cause of a system that has quietly lost half its performance without failing outright.
Water gets into a coaxial connector far more easily than people expect, usually through a joint that was never properly sealed or a boot that has perished. Once inside, it corrodes the braid and the centre conductor, and corrosion does not undo itself when the weather clears. A connector in that state still passes a signal, which is exactly why it goes unnoticed. It simply passes less of one every year.
Replacing a corroded connector is cheap, quick and frequently the largest single improvement available on an older system. It is also the reason we open the joint and look rather than reseal over the top of it: a fresh wrap of tape over a green connector preserves the fault beautifully.
Cable, and the part of the run nobody looks at
Coaxial cable loses signal along its length as a matter of physics, and a long run loses more than a short one. That is worth knowing when a dish has to go a long way from the decoder, but on an ordinary house it is rarely the main problem. What is the main problem is condition.
A cable that has spent ten years on an exposed roof or clipped along a north-facing wall has been cooked. The sheath goes chalky, then cracks, and once it has cracked the run takes in water at every split. The ends can be immaculate while the middle of the run is the reason the picture breaks up in the rain. It is also why a system can be re-aimed, refitted with new connectors and still perform badly, and why we look at the whole run rather than the two ends of it. Where the cabling was rushed at build time, that often becomes a cabling and tv points job rather than a signal repair.
Sealing, because water is a slow thief
Everything above has the same underlying enemy. Water entry is the mechanism behind corroded connectors, degraded cable and failed LNBs, and sealing is what keeps it out. That means proper self-amalgamating tape at outdoor joints, a drip loop so water runs off the cable instead of down it into the connector, entry points into the house sealed from above, and an LNB cover that is actually still in place.
It costs almost nothing at installation and is the first thing skipped by whoever was in a hurry. Houses near the sea suffer for it fastest, because salt-laden air attacks the same joints from the outside while water attacks them from within, which is why we redo joints rather than inspect them on jobs in places like Bloubergstrand.
The upgrades that are mostly not upgrades
| Suggested fix | What it actually does |
|---|---|
| A bigger dish | Collects somewhat more signal, but only if the aim, cable and connectors are already right. On a normal domestic site it is a large, expensive, wind-catching answer to a problem that is nearly always alignment or water. It also makes accurate aiming harder, not easier, and gives the wind more to push on. |
| A signal booster or amplifier | Amplifies whatever it is fed, including the noise. If the signal reaching it is already degraded, a booster gives you a larger degraded signal, and a decoder cannot decode noise no matter how loud it is. |
| A new decoder | Fixes decoder faults. It does not change how much signal arrives at the back of it. Swapping the box when the fault is outdoors is the most common wasted purchase we see, and the symptoms that genuinely point at the box are covered on our decoder problems page. |
| A Smart LNB | MultiChoice describes it as combining the features of a DStv Switch into a single UniCable LNB, offering a single cable solution for distributing multiple satellite signals. That is a distribution device for feeding several decoders down one cable, and it is worth having for that reason. It is not a fix for a weak signal, and DStv states it is not suitable for multiple unit dwellings at all. |
| Thicker or more expensive cable | Worth doing on a long run or when replacing a degraded one. Worth very little as a standalone upgrade to a short, sound run that is already working. |
The order we would spend money in
Measure before changing anything
A reading at the LNB and a reading at the decoder locate the loss between the two. Without that, every subsequent decision is guesswork with an invoice attached.
Open and replace the outdoor connectors
Cheapest item on the list, most likely to be the culprit on any system more than a few years old, and it has to be done anyway before an aim is worth trusting.
Make the mounting rigid, then aim on a meter
In that order. Aiming a dish on a bracket that flexes produces a number that is true for about a week.
Replace cable only where it is actually degraded
A full recable is sometimes the right answer and is often sold when a single damaged section is the problem.
Only then consider moving or enlarging the dish
Reposition if something has grown or been built into the sight line. Enlarge only if the site genuinely cannot deliver, which is uncommon on an ordinary Cape Town rooftop.
Worked through in that sequence, most weak-signal jobs are finished before the expensive options come up. If you are still on step one and trying to work out whether you have a signal problem at all, the codes on the screen sort that out quickly, and the signal fault page explains what each one narrows things down to.
Getting a reading on your own system
Nobody can tell you how much improvement is available on your installation without measuring it. We do that as part of ordinary DStv repair work across the city, including out in Durbanville and the northern suburbs, and the measurement usually settles quickly whether you are looking at a connector or a bigger job.
Questions we get asked
Is an old dish worth replacing with a new one of the same size?
Do satellite signal boosters work?
Would a new LNB improve a signal that is weak rather than dead?
Does the length of the cable run cost me much?
Is there anything indoors that would make a difference?
How much improvement is realistically on the table for an old installation?
Get it sorted
Book a technician
Tell us the make, the size and what the screen or decoder is doing. We will give you a time slot and a quote before anyone starts work.
218 Thornton Road
Thornton, Cape Town
info@capetvrepairs.co.za